Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Faceplate rings vs. faceplates

Posts

Faceplate rings vs. faceplates

#1

Faceplate rings vs. faceplates

wilbur

>I have an old Walker-Turner lathe that is great except for the oddball spindle thread of 1"x12 tpi. I'm having a hard time finding a small faceplate with this thread size. I've got the Vicmarc VM100 chuck, and there is a faceplate ring that I can use with it. You mount the ring to your turning blank, then the ring fits on the chuck.

I was wondering, though, are there any disadvantages of a faceplate ring compared to a real faceplate? It seems to me that maneuvering a big piece of wood onto a chuck would be less cumbersome than trying to thread that piece of wood onto a spindle.

Re: Faceplate rings vs. faceplates

#2

Re: Faceplate rings vs. faceplates

Gordon Seto

>Faceplate rings are more convenient than faceplates.

When you reverse turn, you don't have to remove the faceplate rings immediately. You can still engage the tailstock. That allow you to flip back and forth on both sides to refine the shape.

That is one of the reason I like the Nova line of chucks. Nova has different sizes of their faceplate rings.

Gordon

Re: Faceplate rings vs. faceplates

#3

Re: Faceplate rings vs. faceplates

john lucas

>wilbur I bought one of the faceplate rings but I've never used it. I guess I just don't understand the advantage yet. I thought I would buy them to rough turn a piece and leave them on but they are too expensive to do that.

I do like the idea of being able to reverse turn the piece and leave the ring on. That would enable you go back and forth if needed for some complicated pieces. That's something worth exploring.

See you always learn something when you go to WC.

Re: Faceplate rings vs. faceplates

#4

Re: Faceplate rings vs. faceplates

john lucas

>Oops meant to thank Gordon for the reverse turn idea but my brain isn't working this morning.

Re: Faceplate rings vs. faceplates

#5

Re: Faceplate rings vs. faceplates

robo hippy

>I have never used one, and almost never use a face plate when turning bowls. I do use one on nautral edge bowls. Instead, I use a forstner bit and make a recess to expand the chuck into. This works well on bowls up to about 18 inch diameter. I turn a recess on the bottom of the bowl for the chuck to expand into for reverse mounting. This way, the chuck never has to come off.

robo hippy

Re: Faceplate rings vs. faceplates

#6

Re: Faceplate rings vs. faceplates

eliot d

>robo h.,

I often read your interesting posts, but I can't figure out this one. How does using an expansion mode chucking method keep you from the necessity of having to remove the chuck when reverse chucking? I just finished a hollow vessel that had been held in an expansion mode, but I had to take the chuck off when I reversed it to clean up the bottom.

Re: Faceplate rings vs. faceplates

#7

Re: Faceplate rings vs. faceplates

Gordon Seto

>John,

Thanks for sharing your ideas. I learn a lot from your wisdom. This would be a boring forum if we are going to thank you each time we learn something from you.

Gordon

Re: Faceplate rings vs. faceplates

#8

Re: Wilbur, I used my faceplate ring...

Allen Neighbors

>today for the first time. I only bought the one that fits my 50mm jaws (SN2) because I wanted to make sure I liked them before I bought the larger sizes.

I love it. I turned a 14.5" bowl from cured Ash today, and it held up just perfect... could take it off, and put it back, and no difference in balance. And it's a lot easier than trying to screw a faceplate onto the spindle.

I'm going to buy the others, now. That way I can have more than one in production, while I'm waiting on epoxy fillers to set up. I'm very well pleased with it.