Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Cutter Tip Milling

Posts

Cutter Tip Milling

#1

Cutter Tip Milling

Eric

>Greetings All! I have attempted to make some small hollowing tools, similar to those offered by David Ellsworth. At his home shop he uses a specially made jig he inserts the square stock cutter heads, held in place with a set screw (similar to a pencil sharpener), slides this jig in a track, foward towards the grinding wheel, knocks off the corners and rounds the back side of the tip for easy insertion into the end of the tool steel. Seeing as I am neither a machinist, nor an expert jig builder, can anyone offer up a suggestion on how to round off the backs of tips instead of holding them in a pair of vice grips and trying to do this freehand. Thanks.

Re: Cutter Tip Milling

#2

Re: Cutter Tip Milling

john lucas

>I don't even use vise grips. While the 3/16 cutter is still 3" long I tilt it so the tool is about 75 degrees up and down and then drag all 4 corners one at a time across the wheel lightly. I do about half the tool(the lower half) at a time and then flip it and do the other half. I have never ground the back end. You only need to take off a hair to make it fit into a 1/4" hole. This method is perfectly safe as long as your grinding the lower half of the tool. I'll cut them to length later and sharpen the tip.

Re: Cutter Tip Milling

#3

Re: Cutter Tip Milling

Bill Hale

>I do the same as John. Just keep the tool rest of the grinder real close to the wheel. I also keep a jar of water by the grinder to keep the work piece cool. I also wet the tool rest to help things slide easier.

Good turning and be safe

Bill in Shgow Low, AZ.

Re: Cutter Tip Milling

#4

Re: Cutter Tip Milling

eliot d

>Hi Eric,

I actually made something out of wood like what David Ellsworth uses . It's basically a disk of wood that turns in a wooden tenon. I found an old keyless chuck to hold the bit ( which is centered in the wooden disk) ;and I turn it with a little crank against the grinding wheel -- just the way Ellsworth does. ( You have to rig up something to hold the whole contraption near the grinding wheel -- not a big deal.) The only hard part was that the old chuck has three -- not four -- jaws, so a square bit doesn't center in it. What I did was find a little square bit holder that I drilled and tapped for a small set screw to hold the bit. Works fairly well. Really doesn't have to be perfect: you're going to glue it into a hole with medium CA glue, anyway.

How's your turning going , by the way? I can honestly say that most of my friends see a big improvement in mine. I have gotten the confidence to turn to 1/8 in thickness through smaller openings. The pieces don't look much different from what I had been doing; but they definitely are ( and feel) much lighter. I sense progress.

Re: Cutter Tip Milling

#5

Re: Cutter Tip Milling

Eric Knutsen

>Well, Elliott I wish I could say I've been busy creating even more havoc in my shop that I did at David's but I haven't. I purchased the big tools from David only to find that I can't even se them since I can't take the tailstock off my lathe. Nice right? So I figured I'd make the smaller ones and finally get to work. I have the drive and desire but my life keeps getting in the way......

Re: Cutter Tip Milling

#6

Re: Cutter Tip Milling *LINK*

MountainMan

>Hey Eric

I just noticed these tips on Amazon... not a bad price??

Grind away!!


amazon dot com

Re: Cutter Tip Milling

#7

Re: Cutter Tip Milling

eliot d

>Eric, What kind of lathe is it? Why can't you get the tailstock off? Are you putting out too many fires?

Re: Cutter Tip Milling

#8

Re: Cutter Tip Milling

Mark Mandell - Gone Round In Jersey

>Eric,

See post below re Silver Soldering. I don't have the time to make David's nifty jig. I just chuck the cutter bit in my cordless drill, turn on the grinder and spin one 'gainst 'tother 'till the peg fits the hole. It's not as precise as David's, and certainly not as cool, but it gets the job done with what's at hand.

mm

Re: Cutter Tip Milling

#9

Re: Cutter Tip Milling *LINK*

Darrell Feltmate

>Eric

Why not make the jig? I just put the tips in the cutting bar, bar in the jig and sharpen. A sharpening jig is a great thing to have.


Sharpening at Around the Woods

Re: Cutter Tip Milling

#10

Re: Cutter Tip Milling

Eric

>Right now I'm laughing hyserically..... I thought about that but talked myself out of it. For some reason I figured maybe the tip would jump to much as you made contact. The other issue is the chuck in my drill is a 3 tooth chuck. It's hard to support the tip completely. I contemplated putting the tip in a 4 jaw chuck with the # 1 jaws and apply a sharpening stone to it supported by the tool rest.

Re: Cutter Tip Milling

#11

Re: Cutter Tip Milling

Eric

>I wish I could say I've been busy at work. I'm still nursing the back injury. I've had office job since 6/11. Had cortisone injections in my lower back. Feeling better now. Should be back in the firehouse by Labor Day. The lathe in a barrel style Craftsman. The tailstock runs along the barrel, encased around it. I'd have to unbolt the tailstock, loosen the headstock and slide the tailstock off. Not worth the time of effort. Guess I just have to buy a better lathe. But don't tell my wife......