Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

WoodFast lathe switches

Posts

WoodFast lathe switches

#1

WoodFast lathe switches

Mark Paulley

>Hello all,

I have a WoodFast short bed lathe I purchased in 2002 from Craft Supplies. The on/off swithces have gone out again just today. You push the "ON" button and nothing happens. Does anyone have this happening to their lathe, even other brands? Just curious.

I hope Craft Supply has more of these swithces. I could not a find a supplier around Louisville that carries these ABB swithces.

Roger at Craft Supplies has been GREAT with knowledge and helping me out but since they do not carry the WoodFast brand I am starting to worry a bit.

Thanks for your help and look forward to any replies.

Mark

Re: WoodFast lathe switches

#2

Re: WoodFast lathe switches

Jim Swank

>I've had a similar occurence on my Nova 3000. It just uses an appliance grade rocker switch. I happened to find one at work.

Re: WoodFast lathe switches

#3

Re: WoodFast lathe switches

Dinyar Chavda

>Even though they don't carry the lathe, one advantage of having bought from Craft Supplies is that they still seem to carry a lot of the electrical and electronic parts. So call Roger. Plus he'll help diagnose what the most likely problem is (in my case it was actually a slightly loose connection on the back of the circuit board, which I seem to have fixed by clamping it down at one edge with a paper clip!)

Re: WoodFast lathe switches

#4

Re: Have you tried to repair the switch?

Al Crandall (N.E. of Indy)

>Just last Tuesday. I was turning on my friend's PM 3520 when suddenly the lathe wouldn't turn on. We unpluged the lathe and took apart the box which contained the remote switch. He figured that if this switch proved to be ok, then the problem was in the main switch in the headstock panel. A continuity check on the switch terminals showed that we had found the culprit. At that point, my mind went into "find a replacement switch" mode, but not Jerry's mind. He figured that if the item was broken he wasn't out anything by taking it apart and looking inside. He dissambled the switch and futzed around inside it for a short time, bending and twisting things so they made more positive contact with each other. Using lacquer thinner and compressed air, he gave all the moving parts a thorough cleaning, and reassembled the switch. The continuity checker then showed the current path breaking and reconnecting as it should, so we installed the switch back in the remote box and I continued on my merry way.

Switches are pretty simple things mechanically inside. You don't need an EE degree to spot a possible problem and give it a good cleaning. If it is broken, why not try to fix it? You can't break it twice.

Re: WoodFast lathe switches

#5

Re: WoodFast lathe switches

Dave Peebles Lyons, Ohio!

>Hi Mark,

I'm with Al on this one. You can't really mess it up. I have fixed a lot of them by just blowing the dust out and checking the connections.

By the way, that lathe you have is one of my favorites. I cut my turning teeth on one. It was a sad day when they quit making them.

Best wishes,

Dave

Re: WoodFast lathe switches

#6

Re: WoodFast lathe switches

Michael Foster

>I have an older woodfast lathe that had a similar problem. My on/off switches are green and red buttons about 1" in diameter. I had them go bad on me once. They just didn't work. Seems like I may have called Woodcraft, but maybe not. I found a replacement switch at a local electrical supplier, but I had to call around a lot before I finally found one. Just make sure they handle the amperage.

Re: WoodFast lathe switches

#7

Re: WoodFast lathe switches

Gary Evans Tallassee, TN

>Hi Mark,

I just happen to have one of those switches on my Woodfast. I converted the lathe a couple of years ago to VFD and an AC motor. I have no idea if the switch is good, as the DC motor is what failed on mine, but I'll put the ohmmeter to it and find out.

If you want the switch, I'll send it along. E-mail an address and pay the shipping.

Gary

Re: WoodFast lathe switches

#8

Re: WoodFast lathe switches

Mark Paulley

>To all a great many thanks!!

I will take apart the switch if I can. Can't really see any places to pull the bugger apart at. I will also give the guru Roger a call and see on parts.

I checked around last time and no one in my area had these swithces.

I have googled ABB and found there are rssp in the USA who may be able to help too.

Gary, thanks for the offer and I may be giving you a call.

Dave, the Wood Fast is my first lathe and have really enjoyed it. Still thinking of moving up to a OneWay 1640 with an outboard. Love that machine. Thought about a Robust but just too much$$$.

Again thanks to all for your help and suggestions.

Mark

Re: WoodFast lathe switches

#9

Re: WoodFast lathe switches

Molly Winton

>Mark, I have the exact same problem with my Woodfast. I got the replacement switch a few years ago, but have been too lazy/intimidated to attempt switching them out. I just bang real hard on my stop switch a few times, and that knocks off the dust inside that causes the stoppage, it starts up and away I go. It's probably very easy to change out, but I've not stopped long enough to attempt it. Roger(?) at CS says with the new switch, it won't allow the dust in again, so I shouldn't have problems after I change it. I'd recommend giving him a call to see if they have the part.

Re: WoodFast lathe switches

#10

Re: WoodFast lathe switches

Mark Paulley

>Molly,

I have found the switches and will be replacing the "ON" switch for now. Replacing them is really simple, it takes about 30 minutes.

This is the second set. I don't think its dust just wearing out the switch. Think about it, you turn your lathe off and on a lot over the course of a few years.

PS: I am amazed at your work and ability.

Thanks

Mark