Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

Speaking of Mark Kauder

Posts

Speaking of Mark Kauder

#1

Speaking of Mark Kauder

eliot d

>If I'm not mistaken, it's Mark Kauder who does these incredible finishes. Has he ever said how he does it?

Re: Speaking of Mark Kauder

#2

Re: Speaking of Mark Kauder

Mark Kauder, Phenix City, AL

>Who was speaking?

Here - I will tell everyone how I do it, and I will tell you why 99.9% of other turners can't.

1)Sand the bowl/HF until you cannot see a single scratch in the wood. None, No where.

2) Spray it with the very best Nitro Celulose lacquer you can find that is made for wood. Must get hard enough to take that abuse of regular handling, but be flexable enough to move with the wood. Look for lacquers formulated for musical instuments.

3) Sand and polish until you see no scratches. None, No where.

The reason all but a few turners will not do it - time. They do not want to spent the time to sand the wood (even for an oil finish) or the lacquer. You hear it all the time everywhere in woodturning - every forum, many demos -"How can I sand faster/easier" and "What is a good-easy finish". Go to one of Bruce Hoover's sanding demos, and he asks who loves sanding, and nary a hand goes up. I love sanding - it make me alot of money.

Mark

Re: Speaking of Mark Kauder

#3

Rob Wallace

Re: Speaking of Mark Kauder

Rob Wallace

>Hey Mark...

I recently bought a quart of "Finesse-it" (....now sells for $ 45 /qt!) and tried it on a few pieces finished with 5-6 light coats of Behlen's "Pre-Cat Lacquer". I sanded to about 6000 with Micro-Mesh, applied the Finesse-It as outlined on your web site, and then buffed that out with a Beall "wax" wheel (both with and without the carnauba wax, almost the same glossiness). Finesse-It does make a difference! Thanks for the tip!! (Do you still use this stuff?) I meant to talk to you in Portland to ask some finishing questions, but I missed you several times, either running to do demo assisting, or to catch a talk. Perhaps in Richmond? I am certain people would love to see your general finishing protocol, materials used, and other finishing recommendations posted on a "how to" page of your web site....have you ever considered doing a demo at the AAW Symposium on finishing?

Your pieces are spectacular ( ...the segments/form AND the finish!)!

Cheers,

Rob Wallace

Ames, Iowa

Re: Speaking of Mark Kauder

#4

Re: Speaking of Mark Kauder

Carole Valentine

>Tell it like it is, Mark! LOL When I think of the gathering in GA, I picture you camped in a chair with a beach towel in your lap, sanding, sanding, sanding, sanding.... ;)

Re: Speaking of Mark Kauder

#5

Re: Speaking of Mark Kauder

Brian Hahn in SW Wisconsin

>Yup. For a really great finish that really shows off the piece, sanding and finishing take much, much longer than the actual turning.

Most people don't have the patience or desire to learn and practice "the Zen of Sanding".

Re: Speaking of Mark Kauder

#6

I"m like Mark,

Terry Quiram, Roanoke Illinois

>I like sanding however it hasn't made me a lot of money (yet). I have to say it was Mark's advise and guidance concerning his process that finally made me see the light. It doesn't take that much longer to do an excellent sanded piece over an ok sanded piece. A well sanded piece makes putting on finish easier. I love watching people rubbing their hands over a great finish. Thanks Mark, you do man!

Terry

Re: Speaking of Mark Kauder

#7

Re: I"m like Mark,

john lucas

>Mark What spray gun do you use. I spend too much time sanding out the slight marks from uneven drying. I'll call it orange peel but that may not be the proper term. It just leaves a slight texture that takes a long time to remove with 600 grit. I feel like I should get a more even surface that would allow me to start with 800 or 1000. Is that a fair assesment. The last piece I just built the finish until could continue sanding beyond 600 without applying any more finish.

Re: Speaking of Mark Kauder

#8

Re: Speaking of Mark Kauder

keith zimmerman, Normal IL

>I remember that too Carole. He was having a great time sanding while in the midst of a discussion. Just sitting there with a towel across his lap and wet sanding one of his pieces. It was a highlight of the many memories of that wonderful week in north Georgia.

keith

Re: Speaking of Mark Kauder

#9

Keith Tompkins

Re: Speaking of Mark Kauder

keith tompkins

>Timely topic.....While in Portland, I was invited to visit the home of Dave Smith. Dave just happened to have two Mark Kauder pieces...and older piece, and a brand-new piece he had just purchased. I know Mark, we have communicated for several years, and I've been meaning to comment about his work for some time.

The difference between the two pieces shows the tremendous progress Mark has made in his work. The early piece, athough well done, shows some sanding scratches, and the finish is unremarkable, appearing very thin,and exhibiting wiping streaks.

On the other hand, the new piece is an absolute jewel. Great pains have been taken in the form of the piece. The joints fit better, and attention to detail in obvious. Attention has been paid to grain orientation. The piece is meticulously sanded, and the finish appears flawless. I overheard comments in Portland that many consider Mark's work among the best segmented pieces being produced today!

So...what is Mark's secret? How did he manage to make such progress in such a short period of time? I'm going to speculate: First, he looked at his work with a critical eye, giving the work an honest assessment, comparing it with the work of others, and more importantly, asking himself this question: "How good can I be if I really try?". I also believe Mark questioned many currently held beliefs about sanding and finishing. How many times have we heard "Sanding past 220 grit is a waste of time"? I think his results prove otherwise.

I know he didn't settle for "good enough". I also know he also looking for ways to improve his work, not just content to use the techniques he was comfortable with. He had a goal in mind, and set out to achieve it.

I also know there is nothing quick or easy about achieving a flawless finish. In many cases, more time is spent in the finishing process than in turning the entire piece. How many of us are willing to make that kind of commitment? I'm guessing at least ten coats of finish, each polished to perfection before the next coat is applied.

I think there is a lesson here. We all have the same choices to make, and the same question to ask ourselves. Am I content with our own work? Is it good enough? Which is more important..Quality or quantity? Am I willing to put in the extra effort to bring my work to the next level? Should I accept conventional wisdom, or push the boundaries a bit? What am I capable of producing IF I REALLY APPLY MYSELF? I think Mark's work answers all these questions.

Mark, I'm proud of you buddy.

Re: Speaking of Mark Kauder

#10

Re: Finishing Rule No. 1

Russ Fairfield

>Rule No. 1

No finish can be any better than the surface under it.

In other words, if you want a perfect finish, you must start with a perfect wood surface. Until someone comes up with a better way to do it, that "perfect" surface will require the use of sandpaper or other abrasive medium and a lot of time.

Those who accept this fact will be praised for their fantastic finishes. Those who don't will have to accept that their finishes will never be any better than mediocre at best. It's as simple as that.

Re: Speaking of Mark Kauder

#11

Re: Speaking of Mark Kauder

Jim Shaver - Oakville, Ontario

>No kidding Mark,

I am like you when it comes to my pens, I get my prepared surface as clean and scratch free as possible....it takes time and it pays off in the end.....like furniture work too, the prepared surface will not hide a scratch under a finish....so my hand planes are my secret weapon.

Take care.

Jim

Re: Speaking of Mark Kauder

#12

Re: I"m like Mark,

Joe Flemig

>John,

I use a Finex FX 100 HVLP detail spray gun. They are reasonably priced and are available at spraygundepot.com. About $90. Joe Fleming

Re: Speaking of Mark Kauder

#13

Re: Speaking of Mark Kauder

Doug Thompson near Cleveland

>I too had the pleasure to meet Mark and see his work at the symposium. His work is perfect (I believe me I looked), the finish, jointery and even passed the last test when you pick it up... balance, weight feels nice.

On top of all that Mark's a good person too.

Re: Speaking of Mark Kauder

#14

Re: Speaking of Mark Kauder

JKJ in East TN

>I also enjoy sanding, but for me it's a kind of zen thing. Much of my sanding is without the lathe turning.

Years ago I ran a small metallography lab and sectioned and polished metals for photomicrography - the mantra is embedded in my brain: use the proper grit sequence, cleanliness is important (loose particles left from the last grit can ruin everything, although far more so with metals), and remove all scratches from the previous grits (plus some to remove the sub-surface deformation). Holding successive grits agains a spinning piece almost guarantees violating the last of these since it is difficult to see when the previous scratches are gone.

Sadly, I see so many otherwise great pieces with beautiful form and incredible figure that are "ruined" by concentric scratches. When I started turning, I heard several people (one an instructor) say they absolutely hated sanding. Unfortunately, their work showed it.

JKJ

Re: Speaking of Mark Kauder

#15

Thanks Joe, I'll look there

john lucas

>

Re: Speaking of Mark Kauder

#16

Re: Finishing Rule No. 1

charlie b

>Corollary to Rule 1 - Use sand paper like it's

free. By trying to get every bit of abrassive

left on a piece you'll likely burn or burnish the

surface. The burnished surface WILL spring

back after a while and any imperfection will

return.

charlie b

Re: Speaking of Mark Kauder

#17

Re: Thanks Joe, I'll look there

Joe Flemig

>I should have mentioned the spraygundepot.com is the internet arm of Tri City Paints located here in San Diego. They are primarily an autobody painting store and they really know their stuff. They are good for air brushes and paints too. Joe Fleming

Re: Speaking of Mark Kauder

#18

Re: Speaking of ....Impossibly LONG

Mark Kauder, Phenix City, AL

>WHOA � Lots of Questions, I will try and hit most of them, though I had intended not to in the first post.

Rob � First, thank you for the complements. ((I just looked at this after writing the whole thing, and someone might think I am slamming you � nothing could be further from the truth. You just hit on some points that needed explaination on how I do it now.)) I seldom us 3M Finesse-It any more. Now I generally sand all the way up to 12000 Micromesh. I found that I still had swirl marks in the finish with it. Swirl marks down at the 5 micron level, are still swirl marks. I never use a machine polishing once I start the wet, hand sanding, again because I have never seen a machine polishing of something as (relatively) soft as lacquer that did not leave marks. Wax � never on lacquer for me. No matter how good the wax, over time it will absorb moisture and cloud up. Wax is a protective coating, whether for a car, or a dining room table. IF you pieces are going to see handling, then yes, wax is possibly required. The stuff I make is generally a �Dust Catcher�, �A Pretty) � in other words, sitting on a shelf looking pretty. NOW having said all that, if you are not taking you finishes to that glass-like look, and you are allowing the grain to show through, then using finesse-it and machine buffing is a great time saver. DEMOS � Never wanted to do a demo on just finishing � I do try to cover most of it when I do long demos (4-5hr). The main reason is, I don�t think I could fill more than about 40-60 minutes, and it would be exceedingly boring. I don�t use any special tool, or gadgets, and I am not trying to sell stuff. Way too many demos on finishing and sanding (or turning for the matter) are 2 hour infomertials for products.

In my opinion, stay away from the any of the catalyzed lacquers. For the most part, they are formulated for the cabinet making industry (and to a lesser extend other furniture). They are meant to be applied to composite type material ( Plywood, and veneered MDF, and the like). They are not expecting to put on more than one or two layers, and they want to be able to shoot them, and ship them out the door the next day. Composites do not move much with atmospheric changes, and the cabinets are expected to suffer everyday abuse. They are HARD and as a result not flexible. If you put on much of a deep coating, it is likely to crack with the movement of the wood. Musical instruments, like guitars, violins, and the like are much like bowls. The wood is fairly thin and moves, and they are handled all the time. You need a finish that will take both of these. Behlan�s Stringed Instrument Lacquer is a great lacquer that is readily available to the public.

Carol and Keith Z. � yeah, yeah�.. OK, True, but I had to get them finished.

Brian � Yes, it can take more time, but if you are not doing a gloss lacquer finish like mine, you can do a very good finish in only an hour of actual work. The majority of that being sanding, and the rest applying an oil finish several times.

Jim � You are the King of Pens in my book. Your pens are flawless, at least the ones I have. :>)

Doug � It was a fantastic pleasure meeting you, too. What you said about my work - Ditto for your gouges.

JKJ � Your comments and sanding protocols are right on.

Terry � Thanks for the complements. Long ago, I heard three wise members, two members of this forum say a couple of things that stuck: 1) Wally Dickerman � �Good enough is never good enough�. By that he meant, If you want to excel in turning (or anything for that matter) each thing you do should be the best you can do. Now the best you can do, is dependent on you current knowledge and skill level, and you should be seeking to improve on both. 2) Russ Fairfield � Russ�s rule number 1, in this tread (along with the corollary mentioned by Charlie B). 3) Terry, maybe you can remember his name, but he was at the first Indy Fest at the demise of the Badger Pond Forum � he brought the Stubby lathe. Anyway, I was pretty much a beginner, and I was complaining online about hating sanding. He told me, �Well then, you are in the wrong hobby�. Sanding as important, maybe more so, than any part of the process.

John � I have several, as you might imagine. Until about a year ago, I used a couple of cheap, small touch up ones from Walmart, Lowes, or Home Depot. I still use them a lot, but I bought an Apollo HVLP conversion �Atomizer� (about $400) about 15 months ago. It is finicky as heck, but it does put a lot more finish on the piece instead of into the air. The thing is with lacquer, all you need to do is get on relatively smooth, and the rest is all in the sanding. Drips and sags can all be sanded out, assuming you have enough finish thickness. Orange peel is a condition that looks like it�s name. It is the result of the finish drying too much in the air before it hits the work surface, usually because of having the gun too far away � 8� is about right. OR it can be from the lacquer setting up before it can flow out � this is usually the result of working in a hot/dry environment. That can be fixed with a retarder, but often as not, you can just thin your lacquer a bit more. Rather than trying to sand it out, just apply another wetter coat over it, to smooth it out. If you have a bad finish, don�t be afraid to start with 320-400 grit to level it out, then recoat.

Joe Fleming � Good to see you are around.

Keith Tompkins � WOW, Thanks. Not sure all is true about me � but let the Myth Begin! ;>}}} Actually, the complements, coming from an artist of your stature, are humbling. Comments: The two of my pieces, the first is over 4 years old. Dave won it in a raffle at the afor mentioned Indy Fest where I had the good fortune to meet many of our forum mates (Dave Smith, Jennifer Shirley, Bill Grumbine, Tommy Skagges, Rod Peterson, Jim Shaver, Keith Zimmerman, Al Crandal, � I Know I am leaving out many). Anyway, at that time, I had probably been turning three years, and segments only about one. My finishes at the time, were �Quick and Easy�. Basic sanding, and wipe on poly. I was later that year, that I saw Elve Jackson at the Carolina Symposium talk about using lacquer. So, I gave it a try, got praise, and continued from there. Joint quality and grain orientation � that is from my favorite segmented turner, Curt Theobald. I was very proud of my first lacquered work, and it was in the instant gallery at Orlando. I grabbed Curt in a hallway, and asked if he would critique my pieces. His first comment was �I don�t like the shiny finish, but that is personal preference, but you are doing it well. However, is this joint up to standard to you?� Wow. My response � �not any more�. Had to not accept �Good Enough� on the joints. Was I trying to be the best I could be, maybe so, but mostly I was hopping not to be embarrassed if my Instant gallery work is placed next to a Curt Theobald, a Don Derry, or a David Ellisworth (joint, finish, shape). I did learn early on, especially working with hard, dense exotics, which you had to sand above 220grit so as not to see scratches. Why do turners have to sand higher (I think 600 is a minimum)? Furniture makers can sand to 220, and then finish, because no one is picking up a dining room table, turning round, and looking at it from 8� out. Our work is meant to be handled, and seen up close. I don�t care if it is a salad bowl, it will be looked at closer than the table it is setting on. You have to be willing to start over on the sanding of the wood, if when you get to 600, you see scratches. Yes, I generally sand the wood to about 600-800, depending on the wood.

Russ � You are my Sensi on a couple of the above subjects. Sanding, certainly a major one of them. Finishing, absolutely. You, the late Sam Simpson, and my father (he was a master car painter, sanding all those cars evenings and in the summer taught me something).

Charlie � Absolutely right. $3000k for the lathe, $100 for the Gouge, $30 for the Bowl Blank, Taking the time to use a little more sandpaper to do the finish right � Priceless.

Well friends, this is terribly windy of me, but it would have been rude not to respond to all the questions.

Hope you are not asleep by now.

Mark

Re: Speaking of Mark Kauder

#19

Thank for the reply, Mark

Steve Mushinski

>Thanks for the reply!

Mark, I took a good long look at your work in Portland and I must say, I too am very impressed with the look.

I also read and took to heart what some of our mentors on the web have had to say. One of the reason I went to Portland was to see Wally and Russ in person to say Thanks.

Keep up the great work Mark!

Re: Speaking of Mark Kauder

#20

Re: Speaking of Mark Kauder

eliot d

>I seem to have started a long thread. I do sand and sand and sand; I don't mind doing it. What I never have done is spray Nitro Celulose laquer and then sand again. I just sand the hell out of it -- up through 1000 grit with Woodchuckers sandpaper (from Canada) so that I can see no scratches -- even with magnifiers. But then I usually just wipe on some tung oil or one of the prepared shellac products. My pieces sell all right at a local gallery; but, if you're who I think you are, my stuff doesn't begin to look like yours. ( I believe I met you at that lunch in Lousiville, and I think I saw your work at the Instant Gallery there. It's has a beautiful glass-like quality, if I"m not mistaken. Do I have the right guy? thanks for your help, in any case.

Re: Speaking of Mark Kauder

#21

Re: Speaking of Mark Kauder

Jennifer@Indy.USA

>.....I think he was sipping some sort of fruity drink with an umbrella and flip flops on too?

:)

Re: Speaking of Mark Kauder

#22

Re: Speaking of Mark Kauder

Mark Kauder, Phenix City, AL

>Could be. www.markkauder.com

Mark