Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

homemade caliper question

Posts

homemade caliper question

#1

homemade caliper question

ken chase

>I'd like to make a device like the one I saw JPaul Fennel use on the dvd from the 06 symposeum where he demonstraates doing a hollowform.I'm not clever figuring how things are constructed and hoping someone can direct me to a plan that explains it.

Thanks

Ken

Re: homemade caliper question

#2

Re: homemade caliper question

Mike Nelson

>Ken, I don't know what type you are referring to but I make home-made callipers from 1/4 ply, thin steel or aluminium. Cut two identical elongated S's, about an inch in the middle tapering down to 1/4 at the ends. Find the center, drill 1/8 hole, flip one 'S' over insert 1/8 nut bolt and you have a set of callipers. Sorry about quick drawing, hope this makes sense.


img

Re: homemade caliper question

#3

Re: homemade caliper question

ken chase

>Thanks so much for takiing the time to reply. Much appreciate it. Think I made an error in my choice of words. The devise Fennel uses measures thickness in hollowforms but is configured differently than a caliper.

Thanks again

Re: homemade caliper question

#4

Re: homemade caliper question

Barry Irby

>Ken, I have made two sets of calipers that are a cross between the ones pictured above and a pair of scissors. They have large curved

jaws on the front and scissors handles on the rear. The handles are the same length as the jaws and you use them like the "s" shaped ones above, but they are much easier. You hold them in one had and slide the jaws into your form or bowl. Since the pivot is centred, the space at the handle end mirrors the thickness on the other end. What I have found though is that you can "feel" the thickness very well with your finger tips in the handles. Its not the exact thickness, but it is proportional and you can feel the changes very well. I made mine out of Plexiglas. If you are interested, I will take a picture and post it.

Re: homemade caliper question

#5

I don't use calipers

TDaniel

>Ken, I drill a few tiny holes in places where they aren't noticable, then I poke a tiny piece of wire in the hole while watching the inside with a flex neck flashlight. I can maintain a perfect thickness all over with this method. When I am done turning the holes will fill while sanding and you can't find them when I am finished. I have bits from .035 to .050. Cost of this rig is about $10 and it works better than anything else I have ever tried for hollow forms.

Re: homemade caliper question

#6

Re: I don't use calipers

eliot d

>tDaniel, I must be missing something: can you re- describe how you do it? I just don't see what you're doing, and I am interested. Have you ever tired the Ellsworth simple loop of wire method?

Re: homemade caliper question

#7

Re: homemade caliper question *LINK*

Dave Peebles Lyons, Ohio!

>Hi Ken,

I have not seen the caliper he used, but I would ask Paul himself.

If he is like most woodturners I know, he will gladly share the info.

Dave


Pauls Page

Re: homemade caliper question

#8

Re: I don't use calipers

TDaniel

>I have tried the wire loop but the drill is much more accurate and easier. I just drill a hole all the way through the vessel at the point where I want to know the thickness. Initially, you can use the drill itself to determine the thickness (if the dril doesn't reach the inside you know the wall thickness is greater than the length of the bit). When you are getting close to the thickness you want just push a smaller bit or a piece of wire or a smokers pipe cleaner through the drilled hole until you can see it by looking from the inside with a flex neck light. You can get this light from "The Sanding Glove". You will need to drill several holes but make sure they are somewhat randomly placed rather than in a row as they may show like a dotted line if placed in a row. You now own the "Daniel Thickness Gage", enjoy.