Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Grinder and jigs

Posts

Grinder and jigs

#1

Grinder and jigs

john lucas

>I've taken the day off from turning to make a much needed stand for my grinder. While I'm at it I've made some jigs for setting the Oneway bracket to the proper length each time for different grinds.

Hopefully this afternoon I'll have time to work on my new grinding jig I'm designing. Oops it's already afternoon, OK maybe this evening. It's going to be a modification of the Ellsworth jig. One thing I don't like about the Oneway Wolverine is that it is too large. When a tool starts to get short, or with some of the mini tools you simply can't use it.

The Ellsworth jig only works properly with tools that are the full width of the jig. I plan to try and make one similar to the Ellsworth but has a V block in the bottom that pushed up on the tool. This should work with just about any width tool as well as spindle gouges.

Now if I can figure out a way to make the angle adjustable also I might really have something.

Re: Grinder and jigs

#2

Re: Grinder and jigs

Chicago Bob

>John,

Please share photos of your oneway sharpening jigs when you finish them. I need to make some for my oneway setup on an 8" slow speed grinder and would appreciate it if you shared your designs.

Thanks,

Bob Haines

Re: Grinder and jigs

#3

Re: Grinder and jigs

john lucas

>Bob When I stop for dinner I'll shoot the jigs. There will be some more in the next issue of American Woodturner. I little birdie told me so.

Re: Grinder and jigs

#4

Re: Grinder and jigs

Jerry Hall

>John,

I have also been messing around with improving and simplifying jig design and have used a wooden version of the Ellsworth jig, that is about 1-1/2 long. It is light and handy and works on short tools. I agree there is an opportunity to simplify jig design and use and that Ellsworth rather than Oneway is the place to start. Two things I have been thinking about to improve it are:

1. Using a cam shaft on the bottom of the jig to quickly lock the tool against the flat top surface. I think this would make it quicker to insert and fix different size tools and avoid messing with turning a threaded shaft. In theory this would be kind of like locking a headstock or tailstock. I am not a metal worker and am still trying to figure how to do this. This should make jig sharpening about as fast as hand sharpening. It wouldn't require a "V" groove either as I see it. Shifting of the gouge a little from side to side should be of no importance.

2. I have been using a fixed leg angle of 23 degrees as recommended by Kirk Del-leer in the Winter 2006 AAW Journal. He also gave a presentation on this at the Portland Symposium, which I missed. But so far using just the 23 degree leg angle has worked fine for me. I am surprised there has been no discussion or comment on his article and viewpoint as it greatly simplifies sharpening setups, if it works.

Keep us posted on your progress, and I would appreciate your thoughts on the above.

Jerry

Re: Grinder and jigs

#5

Re: Grinder and jigs

Bob Stroman

>There's also the Side Grinding jig that appears on the same page as the Ellsworth jig in the Packard catalog. It has the Vee shaped bottom, but the angle is not adjustable.

Re: Grinder and jigs

#6

Re: Grinder and jigs

Barry Irby

>You would need to make the camming device in such a way that it does not slide or drag the tool as it clamps it. That woudl change the setup unpredictably.

Re: Grinder and jigs

#7

Re: Grinder and jigs

john lucas

>here are the setting jigs. I've made one for bowl gouges, spindle gouges and detail gouges as well as one for setting the tool rest to 40 degrees and setting the tool rest for the new trueing jig I made.


img

Re: Grinder and jigs

#8

Re: Grinder and jigs

john lucas

>Here is the bowl gouge jig in use to set the distance of the oneway jig. It touches the wheel in 2 spots which compensates for wheel wear.


img

Re: Grinder and jigs

#9

Re: Grinder and jigs

john lucas

>here is the tool rest setting jig. This is for 40 degrees for grinding the Stewart Batty grind.


img

Re: Grinder and jigs

#10

Re: Grinder and jigs

john lucas

>Here's my new single point diamond wheel truing jig. I made it from plastic decking cutoffs.


img

Re: Grinder and jigs

#11

new grinder stand.

john lucas

>Well it's not done yet but close. I will fill the bottom section with sand. It now has 3 drawers. The top part with the drawer is removeable in case I need to take it with me to demos or classes. It's made entirely from scrap that's been collecting around the shop.


img

Re: Grinder and jigs

#12

Packard Side Grind Sharpening Jig

Jerry Hall

>I haven't seen the Packard jig in person but from the picture it looks like one I built. It was based on the threaded shaft clamping into the flute and centering the tool. It worked well on diameters from 3/8 to 5/8, was light, compact, and easy to handle compared to the Oneway, but had these problems:

1. The orientation across the flute with respect to horizontal was not repeatable. I put an L bracket on the top, to swing down on the flute and that solved that problem. See picture.

2. The final, unsolvable problem for this design was with a tool that had become to short for the screw eye shaft to bottom in the flute. As you tightened down the tool slid on the ramp where the flute tapered off. I suspect that the Packard design may suffer from this. That is why I built one that screwed in from the bottom of a short jig. I could post a picture of this if there was interest.

I still don't like the time it takes to screw in and out for different size tools, that is why I am casually exploring a cam clamp of some sort, from the bottom.


img

Re: Grinder and jigs

#13

Re: Grinder Trueing Jig

Jerry Hall

>John, Slick system. What is the source of your hardware and the diamond point device? Jerry

Re: Grinder and jigs

#14

Re: Grinder Trueing Jig

john lucas

>I made all the hardware. I used some 3/8" all thread. I made the knurled pieces but I don't see why you couldn't epoxy a nut in a wooden knob for the lock, and do the same on the end knob but drill it and pin it so it won't move. I center drilled the all thread for 1/4" which would be easy to do on the wood lathe.

The diamond point was something I picked up from harbour freight for $3 a few years ago. I looked in Enco and they have them from $8 to $12. Mine is 3/8" in diameter with a 1/4" shank. I epoxied the diamond point into the all-thread.

I drilled the plastic decking 3/8" most of the way and drilled it 5/16 for the last 1/2". Then I tapped the last 1/2" for 3/8x16.

Re: Grinder and jigs

#15

Re: Grinder and jigs

Russ Babbitt Jr.

>The picture shows my "story" stick I use to set the angle for my Ellsworth tool. It is used with my Ellsworth jig. I use a similar stick for my bowl swept back bowl gouges ( with the Packard jig ) and another stick for my spindle gouges ( with the Wolverine jig ).

The V block under the stick brings the Wolverine suggested setup more inline with the recommended Ellsworth dimensions. It was copied from one used by David at an AAW demo.


img

Re: Grinder and jigs

#16

Re: new grinder stand.

Chuck Engstrom

>Nice setup, John. I have one on a somewhat broader plank that allowed me to attach a cheapo hand grip to each side -- it's at someone else's shop right now or I'd send a pic. I put the handle on one side near the front, on the other side near the rear, so it would balance OK when I pick it up.

Best--

Chuck Engstrom