Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Filling cracks with silver solder ...

Posts

Filling cracks with silver solder ...

#1

Filling cracks with silver solder ...

Ed Moore

>didn't work for me. I used a good grade silver solder that was lead-free and it wouldn't flow down into the cracks. At just the right instant I poked some in, but as a process it was a total failure.

When Pascal Oudet responded in the earlier thread he told us that Christophe Nancey uses the 2/3 lead alloy type pewter because it maintains a state where you can work it like a putty. Well, my observation this morning is that Christophe has quite correctly identified the problems involved using pewter or solder.

I did purchase some Lab Metal and put it in a crack. It works like a putty, but it probably needs some solvent to make it flow a little better. After it hardens I'll sand it to see if the result is metallic or dull gray. I may use a little thin CA glue around it after I sand it to help it adhere.

I'll update later.

Ed

Re: Filling cracks with silver solder ...

#2

Re: Filling cracks with silver solder ...

john lucas

>Silver solder has a much higher melting point than pewter. There are several grades of silver solder that have different melting points. This is so you can solder a piece of jewelry with high heat or hard solder and then you can solder another piece of metal to it using a lower heat solder. Even the low heat solder is way over the melting point of pewter.

Re: Filling cracks with silver solder ...

#3

Re: Filling cracks with silver solder ...

Mark Mandell - Gone Round In Jersey

>John,

I think Ed's writing about the lead-free solder, now used for plumbing, that is a "silver baring" alloy, rather than full silver solder.

m

Re: Filling cracks with silver solder ...

#4

The Lab Metal filled the cracks ...

Ed Moore

>very nicely and sanded to a nice metallic surface. I filled the cracks in a red oak bowl with it and sanded them later. I like what I got. As expected, it is a shiny aluminum, not a silver, but I'll take it.

I'm not sure what the consistency of the unused Lab metal should be. This is a soft putty and nowhere near liquid form. I used some lacquer thinner as a solvent to make it more conformable.

It is possible that using Lab Metal might give results that are as pleasing as melted pewter.

Ed

Re: Filling cracks with silver solder ...

#5

Gary Knox-Bennett uses...

Craig Daymon

>...some type of high tech stuff that has the same look, but is much easier to work and I don't think it requires heat. He's more furniture than turning, but he has collaborated on turnings with Ellsworth, Stockdale, Sfirri and several others. Unfortunately, I don't remember what the stuff was that he used. He might mention it in one of his books if someone has a copy.

I was watching Nacey on the DVD from AAW yesterday and he also pushes it in with a spatula that he hits the backside of with a torch while he works it. I would imagine this helps him get better penetration.

-Craig

P.S. I apologize for any names I may have misspelled.

Re: Filling cracks with silver solder ...

#6

Craig, I tried using a spatula and ...

Ed Moore

>working the solder into the crack. It was like the punch line of an old joke, "Have you ever tried to poke wet spaghetti up a wildcat's fanny?". I set the bowl on fire in the process and got very little solder anywhere near the crack.

It would interesting to know if other metallic liquid/putties are available.

Ed

Re: Filling cracks with silver solder ...

#7

I thought he just used nails. :)

john lucas

>

Re: Filling cracks with silver solder ...

#8

I have a friend with the book who will lcheck

Craig Daymon

>I'll let you know.

-Craig