Air Quality - My Take - long
Mark Kauder, Phenix City, AL
>I may be repeating myself, but forgive me.
About 3 months ago, it came time for me to close the doors and windows in the shop, and run the Air Conditioning. The day I did, I remembered that last year, the coils of the AC got clogged up when dust collected on moist condenser coils. So, to forstall this, I taped a really good flat air filter to the intake of the AC.
4-6 hours later, that filter was fairly dark with dust - and I had not been working in the shop for the 12 hours before I put the filter on, nor for the 4-6 hours after (working in the yard. This was dust that was so continuing to float in the air, basically days after working in the shop. Ask anyone that has been in my shop, I keep a very clean shop (type A, sorta OCD, and don't want dust/chips in my segmented turning joints). Plus, last year I developed an allergy to Ebony, and it sensitized me to many other woods.
This got me thinking about about air cleaners. Then I started thinking that if I was going to spend $400 for each good air cleaner, maybe my money would be better spent elsewhere.
I started an extended email conversation with Bill Pentz. Bill convinced me that
1) Most Dust Colectors are really chip collectors and dust pumps. They pull out the chunks (including the bigger dust particles, and then pump the really dangerous stuff back into the air (if they got it in the first place). I used my DC a lot, and it is another, not connected) room, and my shop was still filled with dust.
2) Air Cleaners are great for making the shop seem clean (no dust on the shelves and benches), but they cannot cycle air quickly enough to keep the really dangerous stuff out of you lungs. Bill told me of guy that installed a new cyclone in is shop, but had not sealed everything nor fine tuned the drops, yet. Bill was there and they fired up his TS and cut some wood. Even with DC running, it took less than a minute for the air tester they were using to show higher than OSHA allowed dust levels in the shop (this was a double car garage shop, and Bill had to bail because of his resperatory problems. They opened the doors (including the car entrance doors, and put big fans in the exits. They calculated that they were exchanging the air in the shop more than 10 TIMES A MINUTE (I think he said more than that, but I forgot the figure), and it took 20 minutes for the air to return to sub-OSHA standards. Air cleaners are usually set to cycle the air in your shop maybe once a minute or two.
3) Respirators are a good idea. I would even recommend that you wear one. But as my shop example shows, with a respirator you are cutting down on your exposure while you are wearing it, but if you are not capturing the dust at the source with a good DC system, you are just postponing the intake of the superfine dust until you take the respirator off. Unless of course, you put it on before enter the shop, and where it until you leave.
In the end, I decided that what I was willing to do was 1) Upgrade the quality (suction and filtration) of my DC to get what dust I can at the source, and then live with what I cannot capture - while continuing to improve the system.
I decided to replace my 1.5hp Grizzley Cartridge filter DC, with a 1800CFM ClearVue cyclone. I trust Bill's research, so I trusted his recommendations as well. Ed at ClearVue was very helpful with everything. In fact I went to Ed's house/shop when I was up that way about 8 weeks ago. he uses his own system of course - have you ever seen a shop that could have a computer in the shop - a shop that does CNC routing on MDF, that does not have dust on the computer screen? I have now.
Anyway, right now I have the cyclone - and it sucks like a son of a gun. I dropped a 3" jet faceplate next to the DC hose - and it sucked it in 10 feet. It could not quite lift it up 6 feet into the ducting, but..... I am slowly exchanging out my 4" ducting for 6" everywhere right to the machine. I have an old Craftsman TS that I sealed up decently, and now with the DC it is spotless after cutting anything. Some dust still escapes from the back of the blade contact with the wood, but I will be fixing that with an overarm guard/dust port system.
One thing I noticed, I have to empty the DC collection bin faster than I used to - more dust is ending up there. Also, with the better filtration, the room where the Cyclone is, is virtually dust free.
My allergies bug me a good deal less, and I am not working with exotics any less.
Just my experience folks. Take it for what it is worth.
Last Comments:
1) Please read and research completely before sending questions to Bill.
2) Many of us have used/read Bill Pentz's Dust Collection website for years - in my case many years. Most of us don't know that Bill is disabled. He does make a little from royalties that ClearVue pays on every cyclone sale, but no one else that is using his research, and it does not cover his expenses. Read the summary in his DC page, and you can see how to contribute.
Mark