Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

epoxy question

Posts

epoxy question

#1

epoxy question

ken chase

>I have T88 epoxy and need to thin it enough to pour into a hollowform. Is it all right to add acetone or some other solvent to do this? Or will it weaken the epoxy. Afraid I was careless measuring the depth and just beginning to cut through. The epoxy fix will allow me to save the work. Thanks

Ken

Re: epoxy question

#2

Re: epoxy question

john lucas

>Ken I don't know about thinning but if you'll heat both parts before you put them together it will be much thinner. I do this in a pan of water on the stove.

Re: epoxy question

#3

Re: epoxy question

Ron in Drums PA

>Why do you need to thin it?

I've poured thin CA into small hollow forms.

Re: epoxy question

#4

Re: epoxy question

ken chase

>The T88 I use is really thick. It could not be poured.

Thanks for the post!

Re: epoxy question

#5

Let me try again

Ron in Drums PA

>Why do you want to pour epoxy into a hollow form?

Re: epoxy question

#6

Re: Let me try again

ken chase

>I goofed. When I started to part the bottom I misjudged the depth of the bottom, I only began to cut through and If I can pour an inch of epoxy into the bottom I can save the piece. The hole in the top will be so small you won't be able to see the epoxy at the bottom. I'll try heating the epoxy tomorrow and pouring. Hopefully it will work. Thanks for the help.

Ken

Re: epoxy question

#7

Re: epoxy question

RPE

>Use a hair dryer to heat the epoxy up. It will get almost like water. It will hasten the drying time so work fast. I did this all the time fuel proofing radio control airplane cowl parts. I could paint it on.

Remove the 1 from email address if needed.

RP

Re: epoxy question

#8

Re: epoxy question

Gil Jones on Lake Seminole GA

>A little lacquer thinner or denatured alcohol will thin West System Epoxy. I have not used T88.

Gil

Re: epoxy question

#9

Re: epoxy question

Rick Allen

>If the T88 is that thick then perhaps a better solution would be to use a different brand of epoxy that isn't so thick. There are some epoxies which are as thin as water. Most of the marine epoxies are more runny than 10W30.

good luck

Re: epoxy question

#10

Re: Let me try again

Ron in Drums PA

>Interesting solution. Lets us know how it works.

Re: epoxy question

#11

Re: epoxy question

Robert D. Macgregor

>If you could get a small enough (ie, affordable) container of fiberglass resin and some catalyst, it would probably do the same job and be thin enough (well, for a little while, anyway) to pour into the HF.

Re: epoxy question

#12

Re: epoxy question

Don O.

>As Gil said, I have heard of people thinning epoxy with denatured alcohol and painting it on punky wood to solidify it. I also know of a certian artistic woodturner from Schenectady, NY who uses thin epoxy to saturate his work to make it what he calls "archival" so the wood does not exchange moisture and move. He uses very high grade automotive finishes and graphics which can't tolerate wood movment. I believe he uses the West System epoxies which come with measuring pumps to get the mix ratios correct. They have a wide range of viscosities available. Search for their website-very informative.

Good luck and remember to show us how it comes out!

Re: epoxy question

#13

Re: epoxy question

john lucas

>System 3 mirror coat that you can get from Woodcraft is super thin. In fact it will run through the pores of some woods. It's also very clear so I use it on my mirrors when I want to imbed something in clear resin.

Re: epoxy question

#14

Denatured alcohol for thinning epoxy

Dave Smith, Longview, WA

>

Re: epoxy question

#15

You Can Most of the Time

Fog Tanner

>If you use 90% Isopropal alcohol (rubbing), but not more than 10% by volume. I use this quiet a bit for some laminating and finishing epoxies I use. I mix the epoxy in a small plastic measuring cup and then add in the isopropal while stirring. This will thin the epoxy and not affect the strength or cure time. It is always best to try on a small mix of the epoxy you are using. I do this anytime I get a new brand of epxoy.

The alternative is to start with a laminating or finishing resin (epoxy). This is already fairly thin and may suit your application. I actually thin this 10% to get it even thinner for the first application. Bob Smith Industries markets a finishing resin which may be found at most R/C Airplane shops and some woodworking supply. It will normally have the stores name on it and Bob's on the back. It has a 20 min working time so you have to be fairly quick.

Re: epoxy question

#16

Re: You Can Most of the Time

ken chase

>Thanks. I have wanted to try epoxy as a finish but ignorant of the process. Is an epoxy finish done in stages with sanding between as in other finishes?

Ken

Re: epoxy question

#17

Re: You Can Most of the Time

Fog Tanner

>Ken,

If you want to use it as a finish, you need a "finishing resin" or "laminating resin". There are a number of these around, including the Bob Smith brand. I thin the first coat as described, mainly for penetration. I will brush it on with a cheap acid brush, and I usually clean the acid brush (being both a modeler and woodturner). The second and subsequent coats are full strength, which is still thin. For sanding I use 3M Wet or Dry silicon carbide paper, used wet with water. If you put a coat on a day, keeping it leveled as much as possible, there is no need for sanding inbetween. Otherwise, scuff it up with 220 used dry.

Once you have the desired film thickness, add one more. After the last coat sets for a few days, I like to give it at least seven, you can start sanding with 220 wet. You should have done a good job on the lathe with your tools and dry sanding to get it smooth and level. Wet sanding an epoxy finish will only highlight a poor base preperation. After the 220, move on to 320, then 400, 500, 600, 800, and if you are really in the mood, 1200 and then 2000 or 2400. These higher grits are meant for color sanding on automotive paints with the 2000 and higher being used for sanding some clear coats. I also get a lot of my paper from automotive paint supply houses. Especially the 24 and 36 grit Bondo paper I sometimes use.

Wipe clean between coats with a damp Viva paper towel to remove any excess grit. You will be sanding away at least one coat of epoxy, so don't stay in any one place too long as you can get back to bar wood with the 220, a bit harder with 320 and up - but given enough time...

Also keep a fresh supply of paper handy. When it gets dull, change to a new piece, all you are doing with dull paper is rubbing the wood. By the time you get to the higher grits you will have a glass smooth surface which will reflect light. For the ultimate finish you would need to spray on a coat of automotive clear like DelClear or DelGlow and not sand after that. Or you can compund it with one of the 4000 grit compounds, but I don't know that it is worth either the clear coat of compounding. For turned items a good carnuba wax buffed on will work.

Re: epoxy question

#18

Re: You Can Most of the Time

ken chase

>Thanks much for the info.