Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

New Shop

Posts

New Shop

#1

New Shop

Sean Troy

>Finally broke ground yesterday on my new shop. The footers were dug and concrete was poured. Hopfully the block layers will start today. I think redoing the landscaping after all is said and done will take just as much time as the building.


img

Re: New Shop

#2

Re: New Shop

georgetroy

>I hope your plans include an outdoor turning area. You have moved from dry in AZ to wet. The shop is never big enough and you always need more plug-ins and lights. Thanks for showing. GT

Re: New Shop

#3

Very Exciting!

Jennifer@Indy.USA

>Oh, wow, Sean, I'm thrilled for you! I can think of nothing more exciting than breaking ground and creating a new shop from scratch. I can only dream about the day I do that.

Enjoy the journey!

Jen

Re: New Shop

#4

Re: New Shop

Sean Troy

>I should have some room for awhile because after paying for this, I won't have any money to by more tools like a table saw or larger band saw. Outdoor turning sounds like a real joy.

Re: New Shop

#5

Re: New Shop

Carole Valentine

>Congrats, Sean! Build it bigger than you think you will need, have more outlets (lots more) than you think you will ever need (including a few in the ceiling) and a partitioned and sound insulated area for DC and compressor. I am going to have to build a shop when I move to my Mom's house. I am looking forward to a new shop, but I am NOT looking forward to the expense!

Re: New Shop

#6

Re: New Shop

TDaniel

>Sean, I like George's idea of the outdoor turning area. I used to have my lathe set up outside and when the weather is cooperative you can't beat open air turning. I also like a small area that is easily heated for winter turning and indirect sunlight. I don't like having a window that puts me in the direct rays of the sun but I like plenty of natural light. As Carole said, plenty of electrical outlets near the lathe. You may have 3 drills to sand with instead of having to change the pads and it is nice to be able to lay one down and pick up another without having to switch plugs each time. Enjoy!

TD

Re: New Shop

#7

Re: New Shop

Sean Troy

>I'm going to make a area outside for my Mini lathe to turn when the weather permits but not the 4224. I don't think moving a 1,000 lb. lathe around will be to good for my back. I've been working with my electrician who happens to be a friend and will have outlets installed at different levels including the cieling. Plenty of them. Four of them will be 220v. With a 20 space panel that leaves me 12 breakers for 110v. I have to decide in the next day or so if I'll be putting in a floor outlet or two so I can add the conduit before the pad is poured. Im going with a wall unit for air conditioning and have not decided on heat yet.

Re: New Shop

#8

Re: New Shop

Jim Shaver - Oakville, Ontario

>Very Exciting Troy!

I am very happy for you, nothing like a hole in the ground to build your dreams on...:-)

I know it will be a fantastic adventure, keep us posted...

Take care,

Jim

Re: New Shop

#9

Re: New Shop Heating and Air Conditioning

Stuart Johnson

>Has anyone looked into installing one of those hotel room type heating/cooling units. Other than possible filter problems it seems like one of those self contained units would work well.

Re: New Shop

#10

Re: New Shop

Ron in Drums PA

>Congrats Sean

My wife has been pestering me to build a shop for myself so I'm going to watch your progress with interest.

Re: New Shop

#11

Re: New Shop Heating and Air Conditioning

Tony - Memphis

>Mine is not a hotel type really, but it is a heat/cool unit. That's what I've had in my shop for the last nine years. I'mon my third unit. The first one was a Goodman brand and was never a good unit. The second one had a bad fan motor and I couldn't get a replacement. After some research, I got a GE (Home Depot online). It seems to be much better made than the other two. This model is not a heat pump, it has resistance heat. So far, I have been happy with the setup. I built a frame over the unit to hold a pleated filter to keep the dust out. Works very well. Doesn't seem to cost much to heat/cool my 16x20 well insulated shop.

Tony

Re: New Shop

#12

Re: New Shop

Jorge Castaneda

>> Outdoor turning sounds like a real joy. <

It is in the summer, specially when it comes to sanding, put your back to the wind and sand away. Seriously, turning outdoors is a blast.

Jorge

Re: New Shop

#13

Re: New Shop

George Van

>Congratulations Shawn, obviously it will never be big enough but you know that ;-)

Lots of outlets is a good idea, I just spent a couple of days adding more outlets and circuits. I now have 7-110v, 1-20amp 240, and 3- 30amp 240v hanging from the ceiling. I thought I had enough with the walls but then I had extension cords running to the middle of the room everywhere for grinders, lathe lights, sanding, shop vac, you get the idea.

Think about lights in the attic, put a switch right where you enter or on a wall. You could also put a couple of blank circuits up in the attic in separate junction boxes so you don't have to fish them when you decide to add more. Three wire w/G give you the option of 240 or two circuits.

As others have mentioned, vacuum outside shop would be nice.

Re: New Shop

#14

Re: New Shop Heating and Air Conditioning

Steve Russell

>Hello Stuart,

I recently changed out the air/heating in my studio and I looked at lots of equipment, including the self-contained hotel type units, ductless systems, heat pumps, monkey's on treadmills with fans blowing over ice (Hehehehe, just kidding) etc. For years, I operated on window units in the studio and although they worked to a degree, they were never able to keep up with our brutally hot and humid summers... To the degree I would have desired anyway. :-)

I'm lucky in that my A/C bloke is very skilled in his job and I consulted with him quite a bit on what I wanted and what products would meet my needs. One of the problems I always had with the window units was the quick clogging of the filters, not to mention the constant noise. I made up prefilters for the units to help with the dust, but that only worked to a degree. I've stayed in a tons of hotels when I was demonstrating and I'm familiar with the units many of them put in the rooms.

I think these might work, but you still have the noise problem and the filter problem. I opted for a Trane split a/c and heating system, the kind where the compressor is outside and the heater and air handler/ducting is located upstairs. It was expensive but its a dream... :-) It's very quiet and it cools super fast (my studio is 30' x 30'). The heater is sweet and works like a charm as well.

If you go with some type of combined system, it might be a good idea to have an a/c bloke (or yourself if you're handy) build you a prefilter box that will use the newer 5", or 6" thick pleated filters. I use *near* HEPA type filters as my primary filter and the 6" pleated (in-line) filter before the cooling coils. This has worked *really* well for me. My system has been in a year or so and I've changed my prefilters, but the box filter looks fine so far. You can buy these box filters and Home Depot and Lowe's. I looked at my coils and they look new, without any visible dust on the fins.

If you can build one of these prefilters, your life will be much easier and simpler and you will not have to clean your a/c internals nearly as often. I really liked the look of the Mitsubishi ductless systems... Take a look at these. They use a 3" hole through the wall and mount on the wall, not in the window. The noisy parts (compressor and it's fan) are located outside, so they run quieter.

I should mention that I also use "point of service" dust collection through a 6" hose when sanding and also a secondary large air filter collection unit as well. Very little dust escapes these two units, so my a/c filters are not overworked. Whatever you decide, get ample cooling capacity... IIRC, you're in Texas, or as we like to say HOTexas down Houston way, so you need lots of cooling capacity when the temps hit 100 degrees plus, with 99% humidity. :-o Good luck to you and best wishes in all of your woodturning endeavors!

Steve Russell

EWW, WVP

The Hot, Wet and Humid Woodlands, Texas :o