Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

I Finally Did it!!! Exceeded my depth L

Posts

I Finally Did it!!! Exceeded my depth L

#1

Andy DiPietro

I Finally Did it!!! Exceeded my depth L

Andy DiPietro

>Hi Everyone,

After 12 hours of turning, hollowing, more turning, more hollowing, sanding, soaking , a nap, more hollowing & turning, finishing, four Tylenols, two 30-gallon bags of chips and a few prayers and a run-on sentence, it was done. This maple burl hollow form ended up at 11-�� wide x 13 �� high, 2 1/4� collar x 3 1/2� base x 1/8� wall . Up to this month my tallest hollow form was around 9� high.

I used Don Derrys Laser hollowing rig with a 5/8 square bar up to 10� deep. I probably could have finished the bottom with his rig but I chickened out. I then switched to my Pro-forme tool attached to a Don Pencil pistol grip fore arm rest and finished the bottom. I keep checking the wall thickness with Don�s rig and a Calpac CP-TI-327-VBD laser.

Pic3 is a group photo from the same Maple log. The smallest is 8 �� x 9�h and the middle piece is 10 �� x 10� h.

Critiques are welcome. I think I am just crazy enough to try it again.

Off to my woodpile to turn some more.

Andy DiPietro


img

Re: I Finally Did it!!! Exceeded my depth L

#2

Andy DiPietro

PIC2 

Andy DiPietro

>


img

Re: I Finally Did it!!! Exceeded my depth L

#3

Andy DiPietro

Group Photo 

Andy DiPietro

>


img

Re: I Finally Did it!!! Exceeded my depth L

#4

VERY Impressive and pretty, too! : )

Ruth Niles

>

Re: I Finally Did it!!! Exceeded my depth L

#5

Re: I Finally Did it!!! Exceeded my depth L

Danny Wells

>Those are all great looking forms!! Well done Andy!!!

Re: I Finally Did it!!! Exceeded my depth L

#6

Re: Group Photo

john lucas

>Very nice Andy. I'm still sanding and applying finish to my biggest hollowform ever. Mine is only 10 3/4" high. It is vastly different than turning 5 to 7" vessels. I kept having to change the bars because I don't have complete set of 3/4 inch. I had to turn most of the upper 1/3 with my 1/2" bars and then changed to 3/4. I also don't have a really accurate way to measure vessels that large. I don't totally trust my lazar yet. It has a tendency to slip slightly out of position. I'll have to work on that.

Re: I Finally Did it!!! Exceeded my depth L

#7

Re: I Finally Did it!!! Exceeded my depth L

Robert Jay

>Congratulations! Job well done. Robert

Re: I Finally Did it!!! Exceeded my depth L

#8

Andy DiPietro

Re: Group Photo

Andy DiPietro

>Thanks John,

I have to disagree with "only 10 3/4". Making a hollow form that tall is something to be proud of. Also you have to let out a sigh of relief when you take it off the lathe knowing you did not plow through the sidewall. Did you make or buy your hollowing tools?

Does someone make a caliper that measures up to 15" or do you have to make one?

Andy D.

Re: I Finally Did it!!! Exceeded my depth L

#9

Bob Moffett

Re: I Finally Did it!!! Exceeded my depth L

Bob Moffett

>Those are outstanding. I would say that was time well spent.

Re: I Finally Did it!!! Exceeded my depth L

#10

Re: Group Photo

john lucas

>Andy I totally agree with the big sigh, except in this case it was a really big sigh since I did blow up the first one. This is a piece for an article I'm writing on photographing really glossy woodturning so not only did I have to do a decent job of turning I have to really shine on the finishing. It probably won't match Mark Kauder's but I'm shooting for that.

I would like to have some sort of measuring device similar to Keith's bowl measuring device. Even better would be some sort of device like they have in the metal industries that reaches in and touches the insides and gives you an exact plot. Even better would be something that senses where your cutting tip is in relation to the outside of the vessel. It would have yellow light when your getting close to your "set" wall dimension and a red light when you get there. I flashing red light with siren when it thinks you might cut through.

I did make all my tools but If I keep turning the shapes I'm turning now I am going to have to make some more. I make my tops too flat so it's hard to get a tool into the transition from top to side. I more or less copied John Jordan's tools but I think I need to make one that has the cutter mounted at about 30 degrees instead of straight out the tip.

On my 3/4" bars I made some like Lyle Jamiesons but I find those only work well if you have a large hole. I hollowed this one through a 1" hole. I have a sorby swan neck but I don't like the cutter I have. I may try to adapt the Hunter #1 tool to this. If I can make it swivel it be a really sweet tool.

Re: I Finally Did it!!! Exceeded my depth L

#11

Re: I Finally Did it!!! Exceeded my depth L

eaglesc

>Have no idea who Don is or anything about the tools you mentioned but that is one beautiful piece of wood and hollow form.

Now you can breath again huh?

Re: I Finally Did it!!! Exceeded my depth L

#12

Well Andy.....

TDaniel

>It looks like you have learned the most difficult part of woodturning......reading the wood and going where it takes you. Those are nice looking vessels! You started with wood that had the "art" buried in it and you found it. There are many ways to go with this hobby, some quick and easy, and some slow but very rewarding. I think doing what you have done is the most rewarding.....you found the buried treasure. A good oil finish on these pieces and you will have treasures. Way to go!

TD

Re: I Finally Did it!!! Exceeded my depth L

#13

Re: Hey, Andy, those look like they...

Allen Neighbors

>took the sap out of you. Gorgeous wood, gorgeous form, that means the 12 hours were filled with tension... making sure you did them just right! Congratulations on your success... and on the new depth!

Andy, I made a large figure 8 caliper from an old stop sign that the highway department threw onto the metal pile at our local landfill. It was stiff enough aluminum to make a good one. The blades on it are only 1/2" at their widest poing. I cut it with a metal blade in my jigsaw.

It will only measure a piece about 8 inches deep, but it would be easy to make a larger one. Do you have any friends that work for the highway department?

Re: I Finally Did it!!! Exceeded my depth L

#14

That is Nice

Frank

>

Re: I Finally Did it!!! Exceeded my depth L

#15

Re: I Finally Did it!!! Exceeded my depth L

Jennifer@Indy.USA

>Nice job Andy, and beautiful wood too. You're much braver then I! I stick to the smaller stuff.

Jen

Re: I Finally Did it!!! Exceeded my depth L

#16

Andy DiPietro

Re: Hey, Andy, those look like they...

Andy DiPietro

>Allen,

Thanks for the compliments. Actually 11 out of the 12 hours were fun and I took a little comedic license there. Using an old stop sign is an interesting idea. That jogged my memory and I found a sheet of aluminum that I stashed away in my garage about 5 years ago. Now all I need to do is design a caliper on AutoCAD, plot it out full scale and glue to the aluminum plate. I have a good Bosch jig saw to cut it out with then sand it. Sounds like work and time away from the lathe. Maybe I can find plans on the Internet some ware.

Andy DiPietro

Re: I Finally Did it!!! Exceeded my depth L

#17

Andy DiPietro

Thank you Everyone!

Andy DiPietro

>I will post a slightly bigger hollow form next time.