Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Happy 4th

Posts

Happy 4th

#1

Happy 4th

john lucas

>Everyone must be either sleeping or partying. I've already had time to ruin a hollow vessel. Cut through the side about an inch from the top. Oh well, it gave me time to play with the 1/2" hunter tool. I went ahead and turned it into a thin wall vase. Hope it doesn't die on me. The rim tried to split. I completely hollowed this with the hunter tool and have a clean enough finish on the inside that I started sanding with 120 and that was only because I got careless and got a minor catch and pulled the thin offcenter slightly. It was getting too thin at that point so I cleaned up what I could with the tool and then decided to sand the final tear out rather than risk blowing up the rest of the vessel. I guess I could always go buy some fireworks and really blow it up.

Re: Happy 4th

#2

Happy 4th from across the northern border!

Bill Howatt

>

Re: Happy 4th

#3

Re: Happy 4th

don central illinois

>Finally a day off with out a lot to do. Took my gradnson fishing, until we got rained out, finished a simple cedar for LOML and turned a little weed pot from some spalted hackberry. Maybe, can get back to the shop this afternoon. Am still having problems making a gentle curve on my hollow forms. Can't seem to the transistion smooth. Oh, well, practice, practice, practice.

Re: Happy 4th

#4

Re: Hunter

John Scheideman

>John,

What do you think of the 1/2" Hunter? I just got the small #1 Hunter and it cuts very well but is pretty slow going. Mine fits on my Stewart hooker bar and it is a little frustrating to have to constantly change the cutting angle. I am interested to know what you think and how you are using the 1/2". Did you buy the whole tool or just the cutter and put it on one of your existing bars?

John

Re: Happy 4th

#5

Re: Hunter

john lucas

>John The tool I got is called a #4 and it comes as a 1/2" cutter mounted in a 1/2" bar. I simply made a wooden handle for it. The bar is a custom fit for the cutter and helps keep it from clogging where the cutter meets the metal support. I haven't had any clogging whatsoever.

I now have the #3 cutter and I think I'm going to make an adaptor to mount it in a 3/4" bar so that I can use it in my arm brace or my captured bar system. I'm going to mount the #1 in one of my 1/2" bars to do some hollowing tomorrow so I can see how it compares to the 3/16" HSS cutters I now use. I may try to make a swiveling adaptor for the tip. There are places I have trouble reaching on my hollow vessels. If I can make the tip swivel on a small adaptor it would reach those places that I have difficulty doing now.

Re: Happy 4th

#6

walnut vase

john lucas

>Here's a quick shot of the Walnut vase I hollowed with the Hunter tool. It's not done, needs more finish. It's about 7" tall, 5" around. The walls go from 1/16" at the top and thickens up to about 1/8" down to about 1 1/2" from the bottom. Then I let it get thicker so it sits more stable. I think it's a good save from a blow up hollow vessel.

I'm not sure I have as much control of the tool as I do a bowl gouge on it's side for this type of hollowing. However the finish I get is much better and I think the control will come with practice. The only reason I had to start with as course a paper as I did was the ripples I got while trying to blend the areas as I hollowed. With more experience using this tool I won't have that problem and could probably easily start with 220 grit.


img

Re: Happy 4th

#7

Re: walnut vase

John Scheideman

>I agree about the ripples and tool control. I need to practice a lot more with the #1 cutter that I got to gain better tool control. I was feeling like I could do better with a gouge too! I ended up changing back to my Stewart teardrop scraper to get rid of the ripples but I'm sure I will get better with practice. I do like the cutting action of the Hunter. Lyle Jamieson told me that he was working on the Hunter tool to refine it a little better. I think it would be easier to use if you didn't have to rotate the direction all the time. Now you've got me interested in trying the larger Hunters.....just when I emptied my entire wallet at the Symposium! BTW-- nice looking walnut piece.

John

John