New oneway lathe 1236 *LINK*
Ron in Drums PA
>
http://www.oneway.ca/
Knowledge You Can Build On — Est. 1998
New oneway lathe 1236 *LINK*
Ron in Drums PA
>
http://www.oneway.ca/
And the advantage is???
Brian Hahn in SW Wisconsin
>Interesting, but I don't see any real advantage, especially for a lathe that small.
Perhaps someone could enlighten me.
Handicap accessible?
Troy German
>
I assume that those who ...
Ed Moore
>cannot stand, such as the folks in wheelchairs, would find this to be a wonderful lathe. Maybe those of us who are healthy now would find a need for it in the "later" years. It would beat watching "soaps".
Ed
Re: I assume that those who ...
nailshooter
>I agree, Ed. The average age of the turners in our local club is middle to later 60s. In this "average", many are well into their 70s. Some are now unable to stand for a long time at the lathe so they find themselves turning less and less, which is a shame since for many this is their only hobby.
Maybe if they bought a lathe like this early on, they could use it in the lowered position when they felt like it in in their later years. The lathe and the turner could grow old together.
Not to mention those that be able to continue to turn after a debilitating injury, or any other reasons that would keep them from turning while standing.
I don't know how many of these they will sell, but it seems pretty thoughtful to me.
Robert
Re: I assume that those who ...
Gordon Seto
>Members at the 2 Clubs that I belong to are mostly retired or close to retiring. The most common off-topic conversations are usually health care related. Sitting down turning may be an option for those whose replacement knees are failing. Trading in their 2436 for this Sit Down lathe may be a good option when moving to assisted living.
This may not be suitable for the young turners.
Gordon
Re: New oneway lathe 1236
Thomas Skaggs, Foothills of Mount Level
>With the way some wood comes off my lathe putting it even lower might have painful consequences! ;-)
Tom
Re: New oneway lathe 1236
Steve Kubien
>I think this is s great thing. Not just for people who cannot stand for long periods (or at all) but for folks with back, shoulder, neck and/or arm problems. With this you can get much closer to the work and keep your tools closer to your body. Sure, you might have to sit down to do that but it seems like a good trade off to me. Well done Oneway.
Steve Kubien
Easy Access for hollowing.
Jennifer@Indy.USA
>I'm not real sure I get it either? I'm assuming that it gets around the non sliding headstock issue. You can stand right in front of the piece and hollow it out. Seems like making a sliding headstock would have been much simpler rather than a system the pivots the entire length of the ways? Yea, others have done it, but who cares?
Jen
Re: Easy Access for hollowing.
Jennifer@Indy.USA
>It looks to me like the ways would be entirely in the way of swinging a bowl gouge? And how could that not be way too low to do anything? You'd be bent over working on the piece. You can't tell me that they did this for people who can't stand? It's a nice thought, but the market would be so minimal? What gives? Anybody know anything about this thing? I'm curious.
Jen
Maybe it is to promote safety shoes
Brian Hahn in SW Wisconsin
>Suppose you are having trouble mounting a blank and it slips...
Now it will hit your feet instead of the bed.
Re: Just guessing again... :)
Allen Neighbors
>but assuming that the average age of full time woodturners is pretty close to my own (67... retirees, etc.) and also knowing quite a few people who have to turn while sitting down (knee and hip replacements, amputees, etc), I'd say the market is for them. There are a lot of paras and quads that turn already, and the number is rising.
Having a way to get the lathe over closer to you when you're sitting down is a boon, and I think it is a good marketing move, on Oneway's part.
Heck, after chainsawing my knee last week, I've wished my lathe would lean over for me!d :)
Re: New oneway lathe 1236
georgetroy
>I would rather have a stool, perhaps on a swinging arm. In fact I do have a stool with a back I cut down of use on the end of Vicmarc Mini lathe. I don't really need it, but for an all day turning demo on the street's it's not bad. Kudos to Oneway. No risk no gain. GT
Wouldn't be easier ...
Ron in Drums PA
>Wouldn't be easier to have the head swing out just like the Jet 1236?.
With the solid/better base on the oneway, you would still have the ability to stand in front of your work and turn a much larger bowl.
Allen you may be right.
Jennifer@Indy.USA
>I guess you may be right. Perhaps there is a market for a sit down lathe when I actually think about it. There are a huge number of senior turners out there. I'll probably glad that there is that option in 20 years.
I guess I was just hoping in the back of mind that they had come out with a sliding headstock! Since my back is dreaming of one these days :)
Jen
There's more to turning than bowls.
Mike Brazeau
>
Re: Allen you may be right.
Allen Neighbors
>I may be glad there's that option sooner than that!
Jen, if your back is giving you problems, you might try raising your lathe a little by slipping a board under the feet. When I turned on Old Griz (Spindle height 40 or 42 inches or so), I was having an awful time with my back and shoulders, and when I got my Oneway, I raised the Spindle height to 49". Haven't had a problem since.
Just a thought that might give you some relief. :)
Of course
Ron in Drums PA
>But how is a tilting headstock like the Oneway, better than a swivel headstock like the Jet, Nova or Poolewood's?
Re: Allen you may be right.
Jennifer@Indy.USA
>Thanks Allen, I may try it to see if there's any change.
Jen
Re: Of course
Mike Brazeau
>Without seeing the lathe and hearing more about it I can't be totally sure but the "SD" would seem to me to mean "Sitting Down". Oneway is aiming at a specific market for people who cannot stand for long periods of time. This position will allow spindle work which a tilting headstock will not. The design appears to allow raising and lowering the height of the lathe as well to suit a variety of heights. It looks to me that the position would be better than trying to sit close to a standard lathe. I am not sure bowls would be that easy on it, but pens or ornaments certainly would.
I have had bouts of nerve pain originating in my neck that don't allow working for long periods of time and find I am working on small projects on my 2436 quite often and enjoying it. Sciatica often seems to want to appear as well when working at the lathe. I think in later years (not even that far off) a lathe the size of the 1236 and the ability to sit and turn could be quite enjoyable.
Re: Handicap accessible?
tm
>As a full time sit-down turner
I'm dying to get next to one and see what it feels like.
I have to agree with others that Oneway maybe looking to the future
and tap into the grey panther market.
Im pretty content with the Nova dvr xp I got 6 months ago but if I was still shopping this machine would put me in a quandry.
Having fits & wishing I was in Portland,
tm
We can be totally sure ...
Raymond, in Trenton NJ
>The last line in their ad copy that Ron linked us to states:
Come and visit us in our booth but be prepared to sit down and be amazed!
The "sit down" reference is intentional. Bravo Zulu to Oneway for thinking outside the box.
Raymond
Re: Of course
Ron in Drums PA
>I took a look at that picture again.
I hadn't realized that the tail stock also tilted, that makes more sense
Re: Of course
don lewonczyk
>Mike, I guess I could look it up but what exactly is sciatica? Im in a simular siuation but like a connective tissue diease and it comes and goes, its what im told anyway. Hope you read this but I'll look it up later, I have a doctors appt. but I have to check my cows before I leave for it. Getting to the oneway, if it,s for people with problems that can't stand or need to be sitting I think they have come up with a great idea. At least they may have expanded the market in a good way and oneway people are a joy to deal with in the first place. Take care, Don L
The real reason
Troy German
>If you're at a particularly hostile demonstration, and people are shooting at you from the other side of the lathe you can tilt the bed, and the body of the lathe will protect your work piece from bullet holes until you're done turning. I saw the Lone Ranger use the same trick on his horse.
Troy