Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

tool steel

Posts

tool steel

#1

tool steel

eliot d

>I just ordered some tool bit stock and some lengths of oil hardened drill rod to make some hollowing tools from Enco . Their prices were fine , but shipping was very high. Does anyone know of a source near Maryland for this kind of stuff? Also, I ordered HSS tool bit stock. Should I have ordered HSS stock with 5% or even 10% cobalt? Now that I think about it, since the tool bit will do the cutting, what's the advantage of hardened drill rod over ordinary mild steel ( that you can pick up at the hardware store) for the shaft of the tool?

Re: tool steel

#2

Re: tool steel

Wilford Bickel

>I don't know if the shipping would be better but I buy my hollowing bits and drill rod from Grizzly. Got an order in from them last week and IIRC shipping on $30 of bits was about $9 - that is not bad with what shipping costs now. I use standard cold roll still to make holders for these types of tools all the time. The hardest thing was making a 3 point tool out of a 5/16 inch short drill rod and having to drill straight into the end of the cold roll. Had to do some imaginative clamping on that one! The hole through the side to tap for a set screw was not a problem after drilling the end hole!!

Re: tool steel

#3

Re: tool steel

Eric Knutsen

>Elliot,

I e-mailed David about this and this was his response.

MSC catalog numbers are:

3/16", 10% "tool bits", cat #02605129, $2.79

1/4", 10% "tool bits", cat #02605160, $2.93

BUT...

Try the Enco website as they're less expensive. www.use-enco.com.

800-873-3626.

3/16" square, 10% cobalt "tool bits", cat. #383-5212, $1.28 each

1/4" square, 10% cobalt "tool bits", cat. #383-5216, $1.81 each

Good luck and have fun.

Eric

Re: tool steel

#4

Re: tool steel

Gil Jones on Lake Seminole GA

>ENCO is reasonably priced, and I usually wait for their "free UPS Ground shipping on orders of $99 or more" deals.

Gil

Re: tool steel

#5

Re: Those with 10% cobalt are

Allen Neighbors

>the ones that I like best... they seem to last longer. My regular HSS cutters which I used to order from Grizzly dull pretty quickly compared to those with 5% and 10% cobalt that I ordered from Enco.

They are still not as long lasting as some that I got from my Father. They are black on the sides, (sort of like Doug Thompson's bowl gouges). I don't know what sort of steel they are, but they turn crushed-turquoise filling with no problems. (Any ideas, anyone?)

I don't know why, but I think if you call in your order to Enco, the shipping is cheaper.

Re: tool steel

#6

Re: tool steel

john lucas

>Elliot Use standard cold roll steel for the shafts. Drill rod is unnecessary for this. It is very good if you want to make the cutting tool out of it. The only real advantage of drill rod for tool making is that it's size is more accurate so if you need to fit it in a handle or tool post then I might use the drill rod.

Re: tool steel

#7

Re: tool steel

eliot d

>Eric,

I was too shy to ask David( believe it or not). I already ordered from Enco -- but I got the ordinary HSS steel. Oh well. Next time I'll spring for the 10% solution. I did order the oil -hardened rod, though. Thanks for your help.

Re: tool steel

#8

Drilling round Cold Rolled Steel

Mike Brazeau

>Wilf - if you have spigot jaws and a hollow headstock it is very easy to clamp the cold rolled steel in the spigot jaws and drill with jacobs chuck in tailstock. Variable speed is also desireable to slow down the drilling speed.

Re: tool steel

#9

Re: tool steel

Eric Knutsen

>Elliot,

I'm shocked!!! You were embarrassed? You're going soft.... Seriously though, I have hit David up with probably 4 e-mails since last weekend for various issues, questions, etc. He's quick to respond. Why not go to the source? :-)

Re: tool steel

#10

Re: Drilling round Cold Rolled Steel

Wilford Bickel

>Good Idea Mike, At the time I did that drilling I did not have spigot jaws but do now so I will keep it in mind for next time. The only problem I can see is IIRC one of the cold rolls I used was 1/2 diameter and I think my big Delta only has a 3/8 inch hole but I will have to check that out.

Re: tool steel

#11

Re: Eliot, check out Darrell

Allen Neighbors

>Feltmates web pages for some top notch information about drilling steel! http://www.aroundthewoods.com You need to sneak up on the size of the hole. His instructions will explain that remark. :)

Re: tool steel

#12

Re: Eliot, check out Darrell

Joe Melton

>I followed Darrell's process and made a couple of Oland tools. I used water-hardened .75" stock from Enco. The shipping wasn't much, probably because I'm relatively close to them, but I did find later that I could have bought cold-rolled steel cheaper at a local steel supplier a mile or so from my home. I used 1/4" HSS cutters from Enco, and some black pipe from Home Depot for the handles. Works the charm.

Joe

Re: tool steel

#13

Re: Way to go, Joe!

Allen Neighbors

>Black pipe about 1/2 full of BBs for ballast makes for a good handle.