Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

SKEWING

Posts

SKEWING

#1

SKEWING

C.W.Stivison

>After all of the post last week about not liking the skew,(I didn't like it all). I decided to take the advice of some of my NBF's at WC and practice. I sharpened up my skew and I honed it this time as someone suggested, loaded a peice of 3" round stock into the lathe and I skewed and I skewed and I skewed, for an hour. The next nite I did the same thing.The skew is still not my favorite tool(that would be my new Doug Thompson detail gouge)but I am not afraid to pick it up anymore. I still don't think it would be one of the first tools I would have a begginer buy. But that's just me.

CW

Re: SKEWING

#2

Re: SKEWING

Terry Quiram, Roanoke Illinois

>I hate the damn thing. No amount of practice (I do a fair bit) is makeing me that much better. I just watched an old Raffin video and he uses the skew for almost all of the projects. I watched Men in Black II right after. Now I know why Raffin is so(abnormally)good with a skew. He is from another planet.

Re: SKEWING

#3

Re: SKEWING

Carol in Illinois

>CW,

I tried using the skew right away when I started turning, and pretty much did so only on the basis of informal, inattentive reading of various ww-ing journals over the last few years. No doubt, I've done some things that would make the pros shudder. E.g., I started out using primarily the POINT to make Vs and beads.

After watching a video someone posted the link to, I was especially provoked when the demonstrator turned from square blank to finished product using ONLY the skew!!! That freaked me out.... so I tried it. Hey! That can actually be done!

I can't get pretty peels off of it yet, though, and while moving from right to left is a snap, left to right is still dodgey.

So... I'm in the "works for me!" camp.

Carol

Re: SKEWING

#4

I ♥ My Skew

Ron in Drums PA

>Actually, I ♥ all seven of my skews

Re: SKEWING

#5

Re: I �� My Skew

C.W.Stivison

>I love alot of things but I don't think it will ever be a skew.

CW

Re: SKEWING

#6

I guess I'm a skew nut.

john lucas

>Like Ron I have at least 7 skews. I turn the finials of my ornaments almost entirely with the skews. I do a lot of work with it that others might think are dangerous but as long as you follow the rules they aren't bad.

It is a hard tool to learn if you don't have someone to work with you. It's hard to write down the subtle things you do to make a skew comfortable. Even a video won't show very well how the skew works. You really need hands on with lots of practice.

Re: SKEWING

#7

I use my skew daily

Rick Davenport

>To hold up the filter on my dust cleaner.

Since I do mainly bowls and such, I don't turn with it enough to be comfortable.

But it IS handy!

;-)

Rick

Re: SKEWING

#8

Re: Terry-we know for sure that ....

Jamie Donaldson

>.... he's from another hemisphere!

Re: SKEWING

#9

Ron and John

Jim Shaver - Oakville, Ontario

>We must be brothers,

I have 7 skews as well and Love them...Just got an Alan Lacer BIG skew...WOW.

Take care,

Jim

Re: SKEWING

#10

Re: I guess I'm a skew nut.

Ruth Niles

>I totally agree, John and Ron. I love my skew, it's the first tool I reach for and can make it do just about anything I want. Ed Moore gave me a small 1/4" round one he made (is it 1/4", Ed?) and I really enjoy using that little guy.

I learned how to turn from a book I took out of the library which was "Turning Projects" by the alien himself, Mr. Raffan. In it he said (*paraphrased) "the skew is the most difficult tool to master but if you do, it will be you (favorite or something to that effect)." It was almost like a dare to me so I used the skew until I feel I've mastered it, almost, sometimes. Now the skew is my tool of choice.

Re: SKEWING

#11

Me, too, Jim and WOW is right! : )

Ruth Niles

>

Re: SKEWING

#12

1/4" round skew nut.

Ron in Drums PA

>I have a 1/4" round skew that Bob Rosand gave me, it is by far my favorite. Around xmas time, I started grinding a Lacer radius on it. It was a great tool to begin with and the radius made it even better.

Re: SKEWING

#13

Must be

Ron in Drums PA

>

Re: SKEWING

#14

Re: 1/4" round skew nut.

john lucas

>Yea I love my quarter inch round one but my favorite is my 3/8" that I made from a 3/8" spade bit with 1/4" shank. I cut the spade bit just below the hole they put in the center of the flat part. I guess it's to help pull wire or something. Anyway I ground sharpened and hardened the tool. It's my reach for tool for all small work. It handles much like the 1/4" skew but has a longer cutting edge.

Re: SKEWING

#15

Re: I think maybe this whole bunch is skewed

C.W.Stivison

>

Re: SKEWING

#16

Does a skew look like this 

Doug Thompson near Cleveland

>


img

Re: SKEWING

#17

My new skew won't cut at all

Gordon Seto

>The picture is the skew that I got from Doug Thompson fresh back from the heat and cryogenic treatment. I can't wait to have the negative rake scraper blank. I don't want to wait till Doug comes back from the Portland Symposium. I thought how hard can a little cleaning up and grinding be.

I have to admit I was wrong. If I have to pay myself minimum wage to do that; then I have put at least $30 added value to the skew. I know it is A-11 tool steel, overheating won't hurt; but I don't want the edge to turn blue.

Hopefully I can find some time to make a handle and play with it tomorrow.

Gordon


img

Re: SKEWING

#18

Re: I use my skew daily

Brian Hahn in SW Wisconsin

>It's also a great scraper to make the dovetails on tenons for gripping with a chuck.

Re: SKEWING

#19

Re: Terry-we know for sure that ....

Vince

>Originally he is from the same hemisphere but currently resides in the other hemisphere.

Re: SKEWING

#20

Re: SKEWING

eaglesc

>When I first started turning pens my only method of sharpening was a table mounted hand crank grinding wheel.

The skew was the only chisel I could put an edge on by myself.

Turning the crank and trying to sharpen the gouge was like patting your head and stomach at the same time.

Eventually I got a Diamond stone.

I use the skew 99% of the time.

They still will not issue me an operator license for a gouge.

Pens have pretty much straight lines.

Why use a curved tool?

Re: SKEWING

#21

Re: Doug, I love my new tools...

Allen Neighbors

>and I want one of these!

Re: SKEWING

#22

Gee, I only have four of them :)

keith zimmerman, Normal IL

>

Re: SKEWING

#23

Re: SKEWING

keith zimmerman, Normal IL

>I watched a demo in my club on the skew and decided I needed to learn this tool. The only thing I had ever used it for was to hollow my first bowl (cringe), but other than that, it was only used as a scraper. After the demo, I had an basic understanding of what the tool could do and forced myself to practice a lot with it. I had so many catches that I almost threw it through the ceiling, but persevered and eventually got to where I use it 95% of the time for turning pens, bottlestoppers, tops, or anything that is turned in the spindle orientation.

keith