Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Grinder Tune Up

Posts

Grinder Tune Up

#1

Grinder Tune Up

TDaniel

>It has been a while since we discussed how to tune up a grinder so let's go thru it again. In a previous discussion Russ suggested starting with the wheels removed.....that is an excellent idea. Start with no wheels on your grinder and if it runs smooth then you know the problems will be in one of two areas...the wheels will be out of balance or the wheels will not be 90 degrees to the shaft. On cheap grinders you can bet that the wheels will not be held 90 degrees to the shaft. On a cheaper grinder if you look at the plates that hold the wheels you will likely see that they are stamped, not machined. Stamped plates just do not get the job done. Machined plates that fit tightly to the shaft and hold the wheel to exactly 90 degrees from the shaft are found only on higher priced grinders but they are very important. The One-way balancing kit includes machined plates that will hold the wheel to the desired 90 degrees off the shaft. Normally you can fix your problem grinder just by adding the One-way plates. If you want to take the time to balance the wheels that is even better. Now if you add the One-way kit after you have already dressed the wheel while mounted to the original stamped plates you are in trouble because when you dress a wheel that is not running true you really throw the wheel out of balance. The weights in the One-way kit may not be enough to get the wheel back in balance. It is best to use the One-way balancing kit with a new pair of wheels. If you ever dress the sides of a wheel you will really throw everything out of balance.

Re: Grinder Tune Up

#2

Re: Grinder Tune Up

Bill McWhirter

>Does anyone know of a source of machined plates other than buying the expensive One-way balancing system?

Re: Grinder Tune Up

#3

Leo Van Der Loo

Buy a Baldor grinder, no need for balancing set;-)

Leo Van Der Loo

>

Re: Grinder Tune Up

#4

Re: Grinder Tune Up

Jerry from Lapel In.

>It simple to dress a out of round or balance if you use the Geiger diamond. take a look at http://www.geigerssolutions.com/trudress.html I first used this method at Arrowmont and since have not had any problems with any wheels or cheap grinders.

Re: Grinder Tune Up

#5

Re: Grinder Tune Up

TDaniel

>If the wheel is wobbling due to poorly machined mounting plates (stamped washers on cheaper grinders) and you side dress the wheels to remove that blurry edge or corner of the wheel you will throw the wheel way out of balance. This is because you will take weight off the right side of the wheel at say the front, and 180 degrees opposite that you will take weight off the left side of the wheel. The problem with this is that there is no way, except luck, that you will take off the same weight from each side. A good wheel dresser will only allow you to screw things up faster.

Re: Grinder Tune Up

#6

Re: Grinder Tune Up

Jerry from Lapel In.

>Having worked in a large tool room for over 40 years and ran about every type of grinder made Td you are wrong. You never dress the side of a wheel except on a cutter grinder on when you are grinding small slots on a Parker on other small dry surface grinders( these run much faster rpms ). You never dress the side of a wheel on a snag grinder not needed if the face of the wheel is running true. The sides of most snag grinders are not designed to be used for grinding. What ever you decide to do grind safely ,I have seen whells blow up and you can get injured quick and bad from a snag grinder.

Re: Grinder Tune Up

#7

Re: Please explain how a Baldor can do that

Russ Fairfield

>I hope you aren't serious. Otherwise, you are going to have to explain to me how buying an expensive grinder is going to automatically balance grinding wheels that are unbalanced as they came from the factory.

Re: Grinder Tune Up

#8

agree mostly

TDaniel

>Jerry, you would never need to side dress a wheel on a grinder that was of good quality as those you would use in an industrial shop so I would agree with you there. The cheap Taiwan grinders, however, have side plates that hold the wheel that are not up to the task. These plates are the thickness and tolerance of a common washer. When you mount a good wheel to these grinders the wheel may wobble because of the sloppy fit of the side plates. I needed a good, clean corner to do something and I dressed about 1/2" of the side. It got the corner that I needed but it threw the wheel way out of balance. I fixed that grinder by replacing the wheel and adding the One-way hub and balancing it.

Re: Grinder Tune Up

#9

Re: Grinder Tune Up

John Lucas

>I've never really had to worry about the side wobble. If it's not off much it doesn't seem to hurt the wheel when you true the top surface. I learned never to true the sides. The inboard washers are the problem and I've had good luck with truing them with a file. Simply put some CA on the shaft and washer to hold it in place and then turn the grinder one (without the wheel and nuts0. Then touch it lightly with a file to remove the high spot. It takes very little to do this.

An out of balance wheel or one that holes that are too large are different beasts. The holes to large can usually be take care of by loosening the nut and move the wheel and re-tightening. This takes a few time to get it running reasonably true but it works. I rotate the wheel by hand with a pencil touching the stone. This shows me where it's high so I loosen the nut and move the wheel away from the high side. Once I get it close I true the wheel. These two procedures have solved the problem virtually every time.

I've always wanted to try the Oneway washers but since my procedures have worked I've never spent the extra money.

Re: Grinder Tune Up

#10

Leo Van Der Loo

Comes with balanced wheels.

Leo Van Der Loo

>

Re: Grinder Tune Up

#11

Re: Comes with balanced wheels.

John Lucas

>But then your missing out on the learning experience that TD and I have gone through. :)

Re: Grinder Tune Up

#12

Leo Van Der Loo

Re: Comes with balanced wheels.

Leo Van Der Loo

>Thanks but no thanks John, I've had my experience with grinders and what goes with it.

The reply earlier was more like a tong in cheek, as I'm always surprised that a "LIncoln ride is expected for a Chevy price".

I have a file here that might help some to improve their grinder without a large $$$ outlay, but you do need some tools and accessories to do it this way not everyone has available.

Have fun and take care

Leo Van Der Loo


img

Re: Grinder Tune Up

#13

Leo Van Der Loo

Re: Comes with balanced wheels. 

Leo Van Der Loo

>


img