Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

boring holes for lamps

Posts

boring holes for lamps

#1

boring holes for lamps

Edward in Vancouver

>Racking my brains on trying to bore a hole, maybe 18" long on a spindle for a lamp. I have at my disposal:

Crptsman 12" tubular steel lathe

Nova mini-chuck (the last of 16 tpi x 3/4 threaded Nova mini chucks)

A decent live center

A decent cast-iron lathe steady (3 wheel type) rigged to a a home made oak base that bolts on the tubular bed

The regular assortment of drill bits, and cheapo- extension pieces normally used for spade bits, (socket type with two set screws)

Now I have seen hollow live centers and lamp augers, but I'm hesitant to buy any party because I'm cheap, partly because the crptsman has a #1 morse taper which is now pretty much obsolete, but mostly because I don't want to buy anymore gadgets until I can competantly use what I have.

I understand that if I were to use a hollow live center, boring from the tail end, I'd use more or less a "regular" type of drill bit. But If I go through the head stock, through the Nova chuck, would I still be able to use a "regular" type of bit?

Thanks,

Edward in Vancouver

Re: boring holes for lamps

#2

Re: boring holes for lamps

john lucas

>Edward A lamp auger won't fit through a #1 morse taper, at least not the 3/8. I think they sell a 5/16 but that might be iffy. A regular drill bit will work but won't follow the center as well. ther reason a lamp auger works is it is only cutting with one cutting edge not two so it is in effect boring the hole like a metal lathe.

You will have trouble drilling 18" but you may be able to drill 9 " from each end. you can drill through the chuck if you have a long enough drill bit.

Before I had the lamp auger I used to drill them from both ends on the drill press and then connect the two with a long drill bit in a power drill. I would drill one end. Then I would clamp a board in the drill press and drill a hole in it. I'd put a dowel in the board and then place the lamp blank with the hole I drilled over the dowel. Then I would drill the other end. This made the two hole align so all I had to do was connect them. It worked pretty well.

Re: boring holes for lamps

#3

Re: boring holes for lamps

Jimiles-Charlotte, NC

>A couple of ideas: In Lowe's ELECTIC Department you will find bits 4 to 6 feet long intended for drilling holes to run wiring - probably $10-$20. What kind of stock are you using? Drilling with a long bit in a drill you will have difficulty keeping exit hole in exact center, but if stock is big enough you could drill it then mount it on lathe using the two holes despite where they come out as the center and round it up based on your hole. Also I have mounted pieces on a temporary jig clamped on a long work bench that got it pretty close. Is the hole to run metal tube or wire? If it is just wire adding a base to your long lamp stock could hide the bottom exit hole's location. Good luck !!

Re: boring holes for lamps

#4

Re: boring holes for lamps

Jimiles-Charlotte, NC

>Boring through headstock: I believe a standard (clockwise )threaded bit would not work unless you could reverse the direction the lathe turns.

Re: boring holes for lamps

#5

Re: boring holes for lamps

Curly Smith

>You can get this set of long drill bits from Harbor Freight for $4 (they have larger sets as well) that are fine for occassional use:

25'' LONG x 1/8'', 3/16'', 1/4'' WOOD BIT SET

You can also make a d-bit, they're cheap and simple to make and will drill straight. Instructions here: Making the drills (if you make one you should note that you'll need to drill a starter hole and you'll need to clear the chips frequently since the bit has no chip clearing capability)

a better picture of the d-bit: d-bit illustration

Re: boring holes for lamps

#6

Re: boring holes for lamps

Edward in Vancouver

>Thanks gentlemen, I'll give the ideas a try. I can get a 3/8" bit in the headstock shaft, and LV has "installer's jobber bits" which are, I think around 12", so maybe I can use them and reverse the spindle half way through.

Stock is, um, western maple, salvaged from palletes. Huge fat 2" thick slabs of maple with clear sections (no nails etc.) of up to 24", still a little green, moisture content of around 20% which makes it easier to turn. Please, don't laugh, I'm still learning to turn, and the palletes are free and offer some surprisingly decent wood. My turning "stash" includes red oak, maple, some kind of birch, and poplar, all from palletes.

Re: boring holes for lamps

#7

Re: boring holes for lamps

Barry Irby

>Edward, I would never laugh at using pallet wood or any other wood. Turners are notorious for finding wood where they can. (Side of the road, fire wood pile, downed by storms, whatever.) Free wood is good wood.

Did you say your stock is two inch? Are your lamps less that two inches in diameter or are you gluing up your blanks? If you are gluing two of these together to make a four by four blank, the thing to do is to cut a groove or rabbet in both pieces and glue the blank up with a hole left down the center. I have done this any times. I cut a short piece of wood to fill the end of the square hole and glue it in. It automatically lines up the two pieces and I mount the stock on the filler. Then, when I am ready, I just drill through the filler with and ordinary bit and insert the pipe. If you don't want to use the pipe, you could epoxy in a short pipe nipple in each end.

Re: boring holes for lamps

#8

Re: boring holes for lamps

Ken Grunke from SW WI

>Edward,

The trick I learned for keeping a long hole straight was from Dave Gingery's book on making a metal lathe from aluminum castings. That was to rotate both the drill and the work (in opposite directions, of course). They keep each other in alignment. Speed and feed should be slow.

In your case, the work held by the steady rest at the tail end, with that end free for drilling with a portable electric drill. Start the hole on center with a drill bit in the tailstock if there's room, or just turn a dimple with a parting or pyramid tool. The work is held by your chuck at the headstock, rotating in the normal direction, as is the drill bit.

It works, I once drilled a 3/4" mild steel shaft that way--it was only about 10" long and I drilled from both ends. The holes met *almost* perfectly, probably within 3-5 thousandths.