Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Potential source of new turners

Posts

Potential source of new turners

#1

Potential source of new turners

Mark Wollschlager

>I was up at Lowes for some plumbing stuff when I was walking by the magazines and out of the corner of my eye I spied WOODTURNING in big letters.

That made me do a double-take.

Fine Woodworking has put out a 'best of' special issue focused on woodturning, called Woodturning Basics.

Its not a bad compilation of articles, a bunch from Raffan, Conover, and others.

Tools, techniques, projects. Spindles, bowls, hollowforms.

Not all of them basic, a couple of eyebrow raisers...but not too bad.

It may end up sending new converts in our direction.

Mark.

Re: Potential source of new turners

#2

Steve Kubien

I picked it up

Steve Kubien

>As a turner with less than one year worth of shavings, I picked it up. There is some good stuff in there from my prosepctive. I especially like the article on green turning and the cover story with William H. Macy.

Cheers,

Steve Kubien

Ajax, Ontario

Re: Potential source of new turners

#3

Agree

Ron McKinley

>I ordered it when it was first announced and got it a week or so ago. It really is a great book not only for the beginner but for the more advanced also. It covers almost every facet of turning......Ron

Re: Potential source of new turners

#4

Re: Potential source of new turners

john lucas

>I have almost all of thier other series. I guess I'll have to run by Lowes today.

Re: Potential source of new turners

#5

Re: Potential source of new turners

jeff myroup

>I found it at Barnes and Noble a couple of weeks ago. I really liked the article on William H Macy. I never knew he turned. I think he does some very nice stuff. I was impressed with his undercut rolled edges. I always liked him as an actor, now I have another reason.

Jeff

Re: Potential source of new turners

#6

I have a copy.

Craig Daymon

>I liked the William H. Macy article. Must be nice to walk in a gallery, see a piece you like, call up the artist and go over for a lesson. A good actor too.

Overall, I enjoyed it. I think it could have used 2 more articles, considering it was targeted at beginners. One article dedicated to sharpening and another to mounting pieces on the lathe. Both subjects make appearances in the articles, but I think separate articles are justified.

Mike Mahoney had a great 2 or 3 page article in FWW about 6 months back with a very clear explanation of sharpening a bowl gouge with swept back wings. (Irish/Ellsworth grind.) That would have been a nice one to include.

Again, overall I thought it was a good issue with not too much cutting a pasting of previous articles from the magazine. (Or maybe I just don't recall all the articles...the lamp I remember.)

-Craig

Re: Potential source of new turners

#7

Re: I have a copy.

Cyril Griesbach

>Craig, The FWW article you mention was good and talking to Stuart Batty at a demo in LaCrosse, WI couple of weeks ago I mentioned that article and he told me that Mike wrote it about Stuart's method of sharpening. Watching Stuart sharpen is what made me ask him about the article. BTW..both very nice guys.

Re: Potential source of new turners

#8

Re: I have a copy.

Craig Daymon

>I tried to buy a PDF version of the article, but they swore they never published it...until I told them what page in what issue. Though, that didn't help, they still didn't have it.

I wanted to have a PDF so I could print copies for the shop. I say "copies" because like other articles that go into the shop, it's sure to be misplaced a few times. I guess I'll have to photocopy.

-Craig