Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Table leg blanks

Posts

Table leg blanks

#1

Table leg blanks

Troy German

>Where does one find blanks for table legs? I would like to build a pine farm table. The legs would be 3x3 or 4x4, not sure which yet, but I can't find a source for the turning stock. If it makes a difference, I live in Northern California.

Thanks for the help,

Troy

Re: Table leg blanks

#2

Re: Table leg blanks

Jay Fischer

>I buy 4" thick planks and them rip and cut down to the desired blank size. If you're in the Bay Area then Southern Lumber or Global Wood Source should have pieces that size.

J

Re: Table leg blanks

#3

Re: Table leg blanks

Curly Smith

>Not sure if this wood will suit you but Bing's has a 3.25" square by 29.5" long blank for $8.30 but your biggest cost might be shipping at 9# per blank from North Carolina.

You can also go with Rocker if you want Cherry, Maple or Walnut and have $90 to spend for a 4" square by 30" long blank ($42 for a 3" square).

Re: Table leg blanks

#4

Re: Table leg blanks

Bob Fawcett

>I glued up my legs from 2 pieces of 8/4 stock.

Re: Table leg blanks

#5

Re: Table leg blanks

Nelson

>Buy the legs from tablelegs.com, unless you just really want to turn them.

Re: Table leg blanks

#6

Re: Table leg blanks

Troy German

>That's what I've done in the past as their finished legs are cheaper than any blank stock that i've been able to find, but I really do want to make my own.

Thanks

Troy

Re: Table leg blanks

#7

Re: Table leg blanks

Troy German

>Can/Should that be done for a table that will be outside?

Thanks,

Troy

Re: Table leg blanks

#8

Re: Table leg blanks

Troy German

>Bing's is very helpful. And no, I don't want to spend $90 per blank when there is a good chance that I will mess up. $8 each with a hefty shipping fee (about $60) is much better.

By the way, the blanks Bing's sell are Rubber wood.

Also, the lady who helped me was extremely nice and a pleasure to deal with.

Thanks for the info,

Troy

Re: Table leg blanks

#9

Re: Table leg blanks

Curly Smith

>As long as you use the right glue for the conditions it will be fine. You can use a polyurethane, an epoxy, or Titebond III. I'd look for one that closely matches the color of your wood, unless you're going to paint it. However, I should mention that Titebond II is water resistant and it would be OK if your table is on a covered porch.

WoodCraft, among others, has a bunch of glues to pick from: WoodCraft Glues

Re: Table leg blanks

#10

Re: Table leg blanks

Troy German

>Thanks, I've called both stores and each said they would have to special order it, but neither has gotten back to me yet with a price.

Thanks,

Troy

Re: Table leg blanks

#11

Re: Table leg blanks

Troy German

>Thanks Curly. I know the glues promise that they will work, but that doesn't mean they will. I don't mind if the rest of the table becomes weathered, I like that look, but I don't want the legs to split apart.

Thanks again,

Troy

Re: Table leg blanks

#12

One other thought

Curly Smith

>Since your table will be outdoors you might consider visiting a local deck supply company. They should have 4x4's of redwood, cedar and other weather tolerant woods; they might even have 4x4 solid color composites that will require no painting when turned. They can also supply you with the wood/composites necessary for the rest of the project.

Re: Table leg blanks

#13

JL

Re: Table leg blanks

JL

>Our "local" lumber store has ash, cherry and hard maple turning blanks (30+" x 3.5" x 3.5") for $17-19 for the ash and maple and $25 for the cherry. I don't know if this would work for your pine table. Of course the shipping would be about $10 each. They can be reached at http://www.hardwoodweb.com/lumber/index.cfm.