Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Jet-1236 question

Posts

Jet-1236 question

#1

Jet-1236 question

David Breth

>Hi -

It's been awhile since I posted anything, but I do keep tab from time to time. Lately I've been prepping for a craft show - my first - so I've been spinning like crazy. Guess we'll find out how it goes, but win, lose or draw, I'm looking forward to it. If I get motivated, I'll share some of my planning ideas and later how it goes.

Anyway, I've got a 1236 question. Is there something that I, an electrical novice, can do to modify the 1236 to get lower speeds for sanding? The lowest the lathe goes is 500 or 550rpm, and I'm thinking that somebody out there has a really clever way to slow the lathe down further.

Thanks very much -

David B.

Re: Jet-1236 question

#2

Re: Jet-1236 question *LINK*

Brian Simmons, Heflin, AL

>The president of our turning club converted his 1236 to variable speed.

Here's the link

http://www.alabamawoodturners.com/newsletters/sep_2006.pdf


http://www.alabamawoodturners.com/newsletters/sep_2006.pdf

Re: Jet-1236 question

#3

Re: Jet-1236 question

David Breth

>Thanks very much, Brian. That may end up being a bit involved for me, but it is definitely the kind of thing I was looking for.

David B.

Re: Jet-1236 question

#4

Re: Jet-1236 question

Ken

>Have you tried a varable speed switch.I have used them on other tools and they worked pretty good.Seem's like if you just used it for sanding it may work for you.Just a thought.

Ken

Re: Jet-1236 question

#5

Re: Jet-1236 question

Bill Howatt

>They are made to work with universal motors (with brushes) and won't work on induction motors. The speed of an induction motor is dictated by the frequency of the power. You can slow an induction motor down by dropping the voltage but it usually causes it to draw too much current.

Bill

Re: Jet-1236 question

#6

Re: Jet-1236 question

David Breth

>So I take it I have an induction motor?

David B.

Re: Jet-1236 question

#7

Nope...

Peter Teubel

>Electrically, your only choice is to replace the motor and install a VFD. That is not even a viable option because the Jet 1236 uses a proprietary motor (very short). A replacement would cut into your swing on the lathe.

Re: Jet-1236 question

#8

Re: Jet-1236 question

Bill Howatt

>Yes. Most motors on larger "stationary" shop tools are induction motors. Portable planers and portable table-saws typically have universal motors. For shop motors the usual give away that they are induction motors is the starting capacitor on the surface which is a cylinderical bump about 6" long and 1" high. Induction motors run much quieter than a universal motor. There are induction motors without the capacitor but they tend to be lower HP than what you find on larger shop tools like lathes, table-saws, jointers.

Bill

Re: Jet-1236 question

#9

Have a look at this solution *LINK*

Bill Howatt

>Note the rear of the picture in post #2. He removed the fan on the motor and replaced it with a large pulley and mounted a second motor down below. The lathe is a Canadian Tire model but it is very similar in design to the Jet1236 like a lot of them are.

Neat trick.

Bill


Slow Speed Method

Re: Jet-1236 question

#10

Re: Have a look at this solution

David Breth

>Thanks for posting that. That might be more viable for me to pull off, or something close to it. I wonder if I could mount a small motor on a pully that would run independent of the Jet motor....

David B.

Re: Jet-1236 question

#11

Re: Have a look at this solution

Ed in Leaside (Toronto, Ontario)

>Thanks Bill for digging that one up. I'd forgotten about that thread.

David, here's another photo with the second motor engaged. This photo is about 2 years older (different sub-bed and extension). To swap to low speed was a simple matter of unplug the main motor, plug in the other motor and hang it off the belt. The second motor is reversible and IIRC it's only 1/4 HP.

Using a small motor and bypassing the main motor is feasible but not very practical. My first attempt at slowing the lathe down involved "borrowing" the gear motor (50 RPM) from my paper guillotine's back gauge, but I had to disassemble the Reeves drive to mount it.

Now that I think of it, one thing I didn't try was driving the spindle directly from the outboard side (1/2 x 13tpi LH). That would be fairly easy provided you had a suitable motor.

Ed


img

Re: Jet-1236 question

#12

Re: Have a look at this solution

David Breth

>That's actually what I was thinking about - attaching to the outboard spindle.

Thanks again - one and all. I won't be spinning for a little while. I'm prepping for my first craft show, and at present have something on the order of 38 bowls on my workbench in various states of finish. Hurry, oil, dry, dry!!

David B.