Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Half Pipe?

Posts

Half Pipe?

#1

Half Pipe?

Thomas Skaggs, Foothills of Mount Level

>The other day I was turning a piece and at the time I was using a small gouge. I took it into a tight place but was trying to get a little sheer. It occurred to me that a bowl gouge, cut in half lengthwise might be interesting. Has anyone tried that? Dumb idea?

I guess you would need two of them for each direction of work. Well anyway, it was just a crazy thought at the moment.

Tom

Re: Half Pipe?

#2

Re: cryogenics and turning tools

Jorge Castaneda

>Tommy,

What have you been putting into that pipe?

Re: Half Pipe?

#3

Re: Half Pipe?

john lucas

>A bowl gouge cut in half lengthwise would be a spindle gouge wouldn't it.

Re: Half Pipe?

#4

Re: Half Pipe?

Ken Grunke from SW WI

>Tom,

Funny you should ask that, I have done exactly what you mention. I approached the idea differently, however. I thought it would be neat to have a skew-like tool but with a slightly curved edge and just a bit of a hollow, or a flute with a broad curve like a continental spindle gouge. My intention was a bowl skew, to make a final clean cut on the interior of a bowl. I made a prototype with 3/8" HSS shaft, grinding a short and broadly-curved flute, and an angled edge like a skew but with a single bevel like a gouge. I did make a double-ender, a left-hand and a right-hand tool. It worked really well, especially with a honed and polished edge.

I thought I was on to something big, and imagined myself on the cover of the Craft Supplies catalog, showing the Grunke Bowl Skew. My delusions of grandeur lasted only a couple hours until I looked at one of my gouges and realized that my new skewgouge was nothing more than a regular gouge split down the middle.

Still, the idea was a good one and I reach for the double-ender occasionally. It goes in one of my setscrew handles, and I use it mostly for spindle turning rather than bowls.


img

Re: Half Pipe?

#5

The Grunke Tool

Thomas Skaggs, Foothills of Mount Level

>Thanks for your reply. Yes, that is similar to what I was imagining. Basically a bowl gouge split down the middle. My thinking is that you could get some cuts in tight areas without the extra width of the other half of the gouge and also be able to avoid catches.

Go ahead and develop it...the Grunke tool just might be a hit! :-)

Tom

Re: Half Pipe?

#6

Re: The Grunke Tool

Mark Kauder, Phenix City, AL

>Seems to me this is just a detail gouge with a special grind on it.

Mark

Re: Half Pipe?

#7

Re: The Grunke Tool

Ken Grunke from SW WI

>That's pretty much it Mark. A broad, shallow flute leaving more than half of the metal below it, and an edge angled like a skew instead of a symmetrical spoon-like shape that a detail gouge has.

Re: Half Pipe?

#8

Re: The Grunke Tool

John Lucas

>Interesting tool. I would be nervous about catching the long point. On the outside of a bowl it would be a lot of fun to use but on the inside I think I would prefer to try something more like a spindle gouge but maybe with a convex curve to the bevel like Russ suggested. I like the idea of leaving the shaft fully round. This would reduce the vibration considerably.

I'll look for the Grunke tool at my local Woodcraft. :)

Re: Half Pipe?

#9

Re: The Grunke Tool

Mark Wollschlager

>I saw a similar grind on a spindle gouge at a Cindy Drozda class.

She got it from another turner ( Priddle, or Raffan I think ) and called it a tornado grind or something like that.

It was good for drilling the center hole of a box and doing the preliminary hollowing.

You had to use it just so. She made it look easy. Noone else in the class could get it to work.

I took some pics of it. I will post one later.

Mark.

Re: Half Pipe?

#10

Let's change the name on that now...

Ken Grunke from SW WI

>I'm not ready to become famous just yet LOL!

Hmmm, I'll have to try that hole boring trick, I can't believe it would be that hard.

Re: Half Pipe?

#11

Let's KEEP the name... Draw it out...

Doug Thompson near Cleveland

>You never know until you try. We use standard shape tools because no one has come up with anything better. Draw it out and when I have time I'll mill them... It just might work.

Go for it.

Re: Half Pipe?

#12

Re: The Grunke Tool

Mark Wollschlager

>Here is pic, similar but different enough.


img

Re: Half Pipe?

#13

Re: Let's KEEP the name... Draw it out...

Ken Grunke from SW WI

>Here's a sketch, Doug, of my idea. My prototype was only 3/8" dia. shaft, 1/2" would be much better. It should have a long bevel like a skew, with an angled edge like one, but mildly curved. The flute should be shallow and of a radius about equal to the shaft's diameter or a bit more. There should be a right and a left-hand edge, maybe both on the same shaft. Call it what you will!


img