Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Kind of OT: Building a shop

Posts

Kind of OT: Building a shop

#1

Steven Antonucci

Kind of OT: Building a shop

steve antonucci

>I'm in the preliminary steps of planning a seperate shop building for my home. I need to work through some things with the town zoning board, but in theory, I'm almost ready to go! (Wife said just do it...)

I was at a local Lowes where they have a 16x24 barn/shed with 2 levels for about $11K. Has anyone ever put up one of these things as a shop? It would be stick built onsite, and the guy said they build them on gravel beds...

I'm also pretty sure I'd have to get a pole and power brought in. Do most towns allow power to a shed on gravel? (I live in NJ) If not, what would a slab or block foundation typically cost in that size?

Any insight to the insanity I'm considering is greatly appreciated...

Steve

Re: Kind of OT: Building a shop

#2

Re: Kind of OT: Building a shop

Randy Johnson Connersville, IN

>If there is any way you can build it yourself you will probably be able to beat the price. Around here there are a number of places that erect yard barns, and in every case I know of the cost is about twice(or more)of what it would cost to buy the materials and DYI. You are going to want insulation and some kind of heat so the money you might save would go toward these upgrades.

I've installed at lot of electical services but I've only put one on a yard barn where the meter was mounted right on the building. Frankly, I was surprised the utility company approved it. Normally when the building is not really anchored to a foundation the meter is set on a pole or pedestal near the building. The feed is then run from the meter to the building underground. They make direct bury quadraplex for this purpose but I still would run it in conduit. It HAS to be in conduit above ground. Below ground the conduit offer extra protection. Odds are it would never be an issue, but if it becomes one about all you can do is dig up everything and replace it. I got involved in one job where the underground for an entire farm had to be redone and have seen a number of less severe cases where the wire/cable being in conduit would have saved the day.

If it's possible the best way to run power to the building would be from the panel in the house.

Re: Kind of OT: Building a shop

#3

Re: Kind of OT: Building a shop

don lewonczyk

>Steve, my sister-in-law just had a 12x30 cooks barn building delivered and set on gravel bed for $6200.00 in giles county TN. Has 8FT side walls and a loft on both ends. It has to be insulated and wiring and the wiring will be run underground from the house breaker. She is beefing up the floor with another 1/2" plywood as she has alot of stuff to put in it. It looks pretty good, you can put doors and windows where you want. Look on the the net and see if they are available in your location. This one was made in MS and delivered to TN. They come unpainted so you can paint it to match its surroundings and it has a shingled roof.

Re: Kind of OT: Building a shop

#4

Re: Kind of OT: Building a shop

john lucas

>Steve In my area you can buy a fully built shed or barn cheaper than you can buy the materials to build one yourself. One of my friends simply bought 2 of them and hand them placed side by side and they installed a walk through between. They were 12x20 each so it made a really nice shop and was ready to go in 3 days.

I looked into this as an option when I was house hunting and was definitely less expensive than building it my self. Of course when you build your own you get exactly what you want. Well not really, there are always choices to be made due to time, money and your skill but still the you do get the satisfaction of building it yourself.

Re: Kind of OT: Building a shop

#5

Re: Kind of OT: Building a shop

Cyril Griesbach

>Steve,

When I planned my shop I looked at all avaiable options starting with stick building it myself. In the end I had a 24x24 garage put up by Best Built Garages which beat my own estimates to do it myself. Got as much space as the township allowed. Ran my natural gas and electric from the house in underground pipe because the utility said I'd have to pay a $15 per month charge for a seperate meter. Once the shop was up I did my own insulating, electrical (with help) and drywall.

Re: Kind of OT: Building a shop

#6

Re: Kind of OT: Building a shop

Bob Fawcett

>Metal buildings are also an inexpensive option.

Re: Kind of OT: Building a shop

#7

Re: Kind of OT: Building a shop

Ralph

>Steve

#1) Check with your LOCAL building code people, odds are not one person here knows the rules your local code may have. Where I live, I could build a building up to 200 sq ft, with a foundation, with out a permit (so I did). But many area's do not allow foundations, other areas will have other rules

#2) Kit prices are almost always cheaper then package-it-yourself

#3) Insulate, insulate, insulate... I really wish I has insulated under the slab

Re: Kind of OT: Building a shop

#8

Re: Kind of OT: Building a shop

Donna Banfield

>Steve, I live in NH, so my costs may run a little closer to yours, being in NJ on the east coast -- or maybe not.

Last spring we cleared and dug the the foundation for our 28 x 40 pad for the 2 story barn. When we estimated the costs for our budget, we planned on concrete costing us up to a max of $90 per yard. By the time the concrete was poured it was running at about $110 per yard, so believe it when you hear that your best estimates will always be far short.

The town we live in required us to dig down 4' deep (to get below the frost line) for the outer walls, which we did on our own with the help of a couple of good friends. We hit ledge at about the 2.5' level for most of it (I guess they call it the Granite State for a reason), and the building inspector still approved it because that entire area was ledge. Gravel was spread over the flat pad. We decided to hire a crew of 3 guys to build the forms, bring the concrete trucks in, pour the concrete and level it. We paid that crew around $5400 for their work and the 3 trucks of concrete.

Re: Kind of OT: Building a shop

#9

Re: Kind of OT: Building a shop

Sean Troy

>How do you insulate under a slab?

Re: Kind of OT: Building a shop

#10

Steven Antonucci

Thank you all for the advice

steve antonucci

>

Re: Kind of OT: Building a shop

#11

how do you insulate under the slab?

Cyril Griesbach

>You place styrofoam panels on the grade, under the reinforcing wire, and pour the concrete over the top.

Re: Kind of OT: Building a shop

#12

Re: Kind of OT: Building a shop

Bill McWhirter

>Steve-

The best advice I got before I built my shop (on a concrete slab) was to put PVC pipes for the dust collector and additional 1 1/2" PVC conduits through which to run electric lines under the slab. I brought them up in plastic boxes (with lids) that are sold for water meters/sprinkler valves which I tried to position where I thought that my equipment would go.

I ran the electric conduits over to the nearest wall, positioned an electrical outlet over them, and ran extension cords throught the pipes. The DC lines end near my dust collector. As clumsy as I am, it is certainly nice to not have cords and hose to trip over. However, I now regret that I used 4" PVC instead of 6" for the DC lines.

Remember the First Law of Shops: "No matter how large you build it, within days of completion, you will wish that you had built it at least 50% larger."

Re: Kind of OT: Building a shop

#13

Re: how do you insulate under the slab?

robo hippy

>You can put in the sub grade (gravel), then plastic or other vapor barrier, them the foam (1 1/2 inch thick), then reinforcing (I prefer rebar to wire as it is easier to keep up in the slab where wire is all over the place up and down). Sometimes the vapor barrier and foam can go under the gravel, sometimes on top. You can put the foam under a vapor barrier. I don't like to pour right on top of a vapor barrier, and will usualy put an inch or two of sand on top of it. All the water comes to the top of the slab and the bottom gets rock hard while the top is still soup. You get more crazing (small hair line cracks)everywhere. You can put foam down the insides of the footings, and even in the bottom and up the outside.

robo hippy

Re: Kind of OT: Building a shop

#14

Re: how do you insulate under the slab?

Ralph

>Robo

I've known more then one person that put the vapor barrier right under the slab, and wondered why the cure time/condition got all messed up (some of the moisture leaves fresh concrete through the ground)