Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

spindle lock for jet mini

Posts

spindle lock for jet mini

#1

spindle lock for jet mini

eliot d

>I just got a new Jet mini. It took me a few minutes to figure out that you lock the spindle with the knock out bar by putting it in the hole on the spindle shaft and holding it against the lathe bed. In other words -- no real built-in spindle . The only problem with the knock out bar method is that you need to hold the bar with your left hand to keep it from falling out. Something tells me that others have already figured out a way to rig something so that both hands can be free to hold a face plate or whatever at the spindle. Am I right? what's the trick, if there is one?

Also , I got the non-variable speed mini because there is no loss of torque at the low end speeds -- as I believe there is with the variable speed version. Am I right that there is loss of torque at the low end for the variable speed?

Re: spindle lock for jet mini

#2

Re: spindle lock for jet mini

Mark Wollschlager

>Eliot,

This is my work around for the missing spindle lock.

I CA glued a small rare earth magnet, smaller than the diameter of the hole in the spindle, at the bottom of the hole.

The thinner the magnet the better.

It holds the knock out bar well enough to use both hands on the chuck.

I leave the other hole open in case I need more leverage.

one way of doing it anyway.

Mark.

Re: spindle lock for jet mini

#3

Re: spindle lock for jet mini

John Lucas

>Eliot I took a flat piece of steel and cut it to fit on top of the headstock. I drilled a hole in it to fit the knock out bar. Then I mounted this on the headstock so that it sticks out just far enough to allow the knock out bar to drop into the spindle. I drilled and tapped the top of the lathe to hold this plate in position. It works really well. I have a photo on my home comuputer if you really need to see it.

Re: spindle lock for jet mini

#4

Re: spindle lock for jet mini

Don O.

>I've had good luck bringing the tool rest close to the headstock and resting the knockout bar on it so it is parallel to the floor, instead of it resting on the bed.

Re: spindle lock for jet mini

#5

Re: spindle lock for jet mini

eliot d

>Thanks for the three different methods to lock the spindle.

How about my other question about loss of torque at low end speeds on the variable speed version?

Re: spindle lock for jet mini

#6

Re: spindle lock for jet mini

john lucas

>Eliot You are very right about the loss of torque at low speed. I've use lots of Jet mini's both VS and non VS. I prefer the single speed motor. I tend to hog off wood when doing demo's because it makes the demo go faster. I stall the lathe a lot when using the VS. I still stall it some using the non VS but not nearly as often.

I find that I tend to use a mini lathe on the same speed a lot so I simply don't spend all that much time changing belts. I find VS much more desireable on bigger lathes.

Re: spindle lock for jet mini

#7

Re: spindle lock for jet mini

Nelson

>If you bought a NEW mini the spindle lock is built in above the outboard handwhell,if not I would return and ask for a new one.

Re: spindle lock for jet mini

#8

Re: spindle lock for jet mini

Leppikallio

>Oh but this is so easy one. You just have to eat more. So that you tummy holding another end of knockout bar forms that spindle lock. In fact this is exactly the method I use also with my Precision Midi chucks. I have always known that my tummy have some BIGGER purpose and now it has. It acts as that famous third hand... :)

Re: spindle lock for jet mini

#9

Re: spindle lock for jet mini

john lucas

>I've always heard Bill Grumbine talking about using his "turning" muscle. We should probably do an article on proper techique of using this muscle. Apparently it's handy.