Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Stuck Face Plate

Posts

Stuck Face Plate

#1

Stuck Face Plate

Ruth Niles

>I just searched the archives for how to remove a chuck or face plate that stuck on the spindle. There are lots of posts on how to avoid this but what do you do when it happens? I just had a piece on a face plate and while I was parting it in the middle, the piece jammed and really tightened the face plate so I cannot physically move it. I also did what someone else had posted; used the index pin to hold the spindle and broke it.

Any suggestions?

Re: Stuck Face Plate

#2

Re: Stuck Face Plate

Ed Heuslein

>Howdy Ruth: What lathe do you have?

Re: Stuck Face Plate

#3

Re: Stuck Face Plate

john lucas

>When you have a faceplate really stuck you should try to lock the spindle at as many points as possible. I wrap cords or straps around the handwheel, then lock the spindle, jam a wedge between the belt and drive pulley so it also will hold a little. The index pin on my Nova is really thick and very close to the wheel so you probably can't shear it but I don't usually recommmend locking the index for this purpose unless you've already locked all the other components.

After you tell us what lathe you have we may be able to help you further. Seems like you had a General at on time.

Re: Stuck Face Plate

#4

General 260

Ruth Niles

>

Re: Stuck Face Plate

#5

and it's REALLY stuck!

Ruth Niles

>

Re: Stuck Face Plate

#6

Leo Van Der Loo

Re: and it's REALLY stuck!

Leo Van Der Loo

>Hi Ruth

If you can bolt or screw a 2X 6 to your face plate, and wedge the spindle/pulley some that would help, but it is the inertia that has to do the most of the job.

You have the 2Xsomething up like in the picture/drawing and really smack that wood down, that should get your faceplate off, you might have to do it a time or two, but it should come off

Good luck, and I also like your NEW website, ;-)))

Have fun and take care

Leo Van Der Loo


img

Re: Stuck Face Plate

#7

Re: Stuck Face Plate

Mac

>Ruth,Check your e-mail....Mac

Re: Stuck Face Plate

#8

Re: Stuck Face Plate

Jorge Castaneda

>Hi Ruth,

Sorry to hear you are in trouble, As they tell you, you need to lock the spindle, what I had to do then was to put a plumbers wrench around the face plate, it is a vise grip with a lenght of chain, and then pound on the vise grip handle with a mallet.

Good luck!

Jorge

Re: Stuck Face Plate

#9

Re: Stuck Face Plate

Mike Nelson

>Hi Ruth, Leo's idea sounds good but you may have to use C-clamps if you can't get screws in. Mine has never stuck that bad but if it did I would put the board on and throw it in reverse. Set the belt to slip a little. If that doesn't work get a hammer drill and thread a bolt through the face plate, doesn't have to be on center, the vibration should shake it loose. Good luck, Butch

Re: Stuck Face Plate

#10

Bob Moffett

Re: Stuck Face Plate

Bob Moffett

>When I have had a faceplate stick on the lathe, I have found that spraying the spindle with WD-40 will help get it loose.

Re: Stuck Face Plate

#11

Re: Stuck Face Plate

Curly Smith

>I would make something along the lines of what Leo suggested and then I would put a strap wrench around the drive sheave and pop the face plate loose. You should get more than enough mechanical advantage from the larger diameter (sheave vs spindle) and the length of the wrench to be successful. If not, your lathe is useless and you should send it to me for a proper burial.

Re: Stuck Face Plate

#12

Why index, it has a big spindle lock pin

Bill Howatt

>Why the index pin? The General 260 has a very sturdy spindle locking pin.

Bill

Re: Stuck Face Plate

#13

Forgot to add:

Bill Howatt

>Since the handwheel is LH thread you can put it on and hold it with the General's wrench and unscrew the stuck plate. Might be a good idea to lube the handwheel threads first to it doesn't get stuck too.

Bill