Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Turning handle question

Posts

Turning handle question

#1

Turning handle question

wilbur

>I'm going to try turning some handles to replace the current ones on my turning tools. I'd like to make them about 14-16" long, which is longer than any of my current handles, so I don't have anything to work off of.

Can anyone tell me how wide is the widest part of your 14-16" handle? Something like, "My Sorby 1/2" bowl gouge has a handle 14" long and is 1 1/4 inch at the widest part."

Thanks!

Re: Turning handle question

#2

Steven Antonucci

Why copy when you can customize?

steve antonucci

>I make most of the handles for my tools, and I've done two things that I think help my control and usage:

1.) Size them for your hands. Mine are small, so my handles are "undersized" compared to normal off the shelf tools. If you have big hands, you might want them larger. Test the fit on the lathe to see if it suits you.

2.) DON'T turn them all the same shape and size! Needle in a haystack? I make each one from a different species or slightly different end (turn some grooves, burn some rings...) so that I can visually identify them hanging upside down from the end of the lathe in 2' of shavings.

Steve

Re: Turning handle question

#3

Re: Turning handle question

Brian Hahn in SW Wisconsin

>I make the handles to fit comfortably in *my* hands. My handles are 1-3/4" in diameter and straight - not curved like the commercial handles. That's what works best for me.

Re: Turning handle question

#4

Re: Why copy when you can customize?

wilbur

>I should have clarified. The reason for asking this question is so that when I start riving the chunks of wood I have to make the rough blanks for the handles I don't make them too small. On the other hand, I don't want the blanks to be too big, either.

Re: Turning handle question

#5

Re: Have you ever seen the handles ...

Jamie Donaldson

>... that David Ellsworth made out of tree branches, complete with some bark! Make them any way that works for and pleases you! Over the years I have made many out of walnut for my own special tools, and used aluminum tubing for ferrules so that they were color coordinated with HSS.

Re: Turning handle question

#6

Leave your options open...

Peter Teubel

>If you accurately drill the hole for the tool shank and you leave the tailstock "dimple" in place, you can rechuck the handle and modify it at a later date....as long as the tool will enter the hollow spindle. The chuck jaw slides will hold it enough for re-turning, if necessary.

Once you find the handle is to your liking, then part off and smooth the tailstock end.

Re: Turning handle question

#7

Leo Van Der Loo

Hi Wilbur, why not take a handle you have that

Leo Van Der Loo

>feels good to you, and make a longer version of that, the size does not have to increase just because you make it longer, it should fit your hand IMO. That's the way I look at it.

Have fun and take care

Leo Van Der Loo

Re: Turning handle question

#8

Re: Hi Wilbur, why not take a handle you have that

wilbur

>Hi Leo,

The turning tools that I have date back to the 50's, and I've figured out that all of them have handles that are too short and too skinny for me. These handles are pretty much straight cylinders.

I'd like to start off by making a handle similar to what you see on a Sorby turning tool -- about 14-16" long, with a wider diameter near the end that the tool inserts into, and narrower in the back.

I was asking my question about the widest diameter of a turning tool to have a good starting point for this project. The reason I'm interested in the diameter is because I have a small piece of straight grained walnut that I'd like to try making into handles, but if it's not thick enough, then I'll save it for something else. I'd hate to start turning it, then find out that it's too skinny and wind up wasting the piece. If it's too thick, I can always cut it down some more.

Wilbur

Re: Turning handle question

#9

Where might one be able to see...

Thad

>...these tree branch handles you speak of?

Re: Turning handle question

#10

Leo Van Der Loo

OK I see, Wilbur I have a Henry Tailor super flute *LINK*

Leo Van Der Loo

>with a long handle, that handle is just a shade under 1.75"D and just about 16" total length, the link should show you what it looks like, it's not my favorite gouge or handle, just a starting point for size, hope this helps you.

Have fun and take care

Leo Van Der Loo


http://www.leevalley.com/wood/page.aspx?c=2&p=20261&cat=1,330,43164,43175

Re: Turning handle question

#12

Re: I studied with David in 1990, and ...

Jamie Donaldson

>... he included the handle turning/tool making segment in one of his early videos.

Re: Turning handle question

#13

Thanks!

wilbur

>Thanks, Leo. That's exactly what I needed.