Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

Drilling aluminum question

Posts

Drilling aluminum question

#1

Drilling aluminum question

Joe Donohue

>I have some thick wall aluminum tubes, 1 1/4" od. The wall thickness is about 1/4", so the id is very close to 3/4" (.727 by my measurement). I would like to try making a few tool handles to accept 3/4" shafts, so I need to remove about .022" from the id.

I know very little about workng metal. I do have a 3/4" twist drill but I could use some guidance about how to proceed. I know from prior experiences that aluminum can be "grabby" and I am not sure the twist drill is the right tool to use.

Can someone give me soom advice as to hoe to proceed? Do I need a reamer? If so, what kind?

Thanks

Joe Donohue

Re: Drilling aluminum question

#2

Leo Van Der Loo

Re: Drilling aluminum question

Leo Van Der Loo

>I would not use a regular twist drill, taking only 10 thou' out, it will grab, but a scraper would do the job, as you need to go in only a couple three inches.

As something I never tried, but think it could work is a forstner bit, it might also grab, but the angle is not as severe as a twist drill, try turning the lathe by hand while feeding the drill, and see what it does, it might work well, make sure you lubricate when drilling, aluminium likes to adhere to the cutting edge, cooling and lubrication do help to minimize.

Have fun and take care

Leo Van Der Loo

Re: Drilling aluminum question

#3

Re: Drilling aluminum question

Carol - Strawberry, AZ

>I've worked a lot of aluminum when I was in the jig making business. Forestner bits polish the sides of a hole. Plunged into aluminum would build up gobs of heat. That makes the aluminum 'gooey.' And the regular twist drill would be very 'grabby.'

This is a job for a horizontal mill with a cutting bit on a bar advanced into the bore and someone who knows how to use it.

I know about gooey aluminum from routing it with a CNC machine. Depth of cut, coolant, and rate of cut were critical to get a clean cut, let alone keeping the cutter from 'welding' itself to the melted aluminum.

Re: Drilling aluminum question

#4

Re: Drilling aluminum question

John Lucas

>Joe The best way is to use a boring bit. If you have a 3/4" twist drill you can probaby chuck the aluminum up in your 4 jaw chuck and take very light cuts. I've done this with my extended jaws but I've never tried it with shorter jaws.

Another option is similar to the machine shop boring tool. If you have a captured boring bar system and use HSS cutters similar to the Jordan or Jamieson system you can simply bore the hole. You coud do it by eye, taking a little bit at a time until you get the whole thing right or you could rig up a couple of stops on the left side of the boring bar to limit it's travel to the left and to prevent you from angling the bar. This could be done by simply clamping some stops on both tool rests. Then you could just bore straight in cutting just the left side the same way you would hollow a vessel.

Re: Drilling aluminum question

#5

Re: Drilling aluminum question

Doug Thompson near Cleveland

>I bore out all my aluminum tool handles with a standard drill bit. This is from solid stock to a ID of .750 with no problems except the handles are 16 to 24 inches long. Set it up in a drill press, couple drops of oil with a speed about 150-200 rpm's.

If you need to plug the end to fill it with sand or shot a 1/2 pipe tap will thread a 3/4 inch hole.

Let us know

Re: Drilling aluminum question

#6

Re: Drilling aluminum question

Curly Smith

>I think I'd either:

- drive a dowel into the tube and then drill with the twist bit (my thought being that having something to drill will help keep the bit from grabbing at the start)

- cover a tapered dowel with sandpaper/emory cloth and let the abrasive do the work

Re: Drilling aluminum question

#7

Re: All you need to do is modify the grind of the

Al Crandall (N.E. of Indy)

>All you need to do is modify the grind of the drill slightly. I could do it in 5 seconds, but I will try to tell you what you should do. Soft metals, like brass and aluminum, can be grabby when drilling if the whole lip isn't engaged. You already know this. The reason it is so is because the spiral flute, by its very geometry, causes a positive hook angle to be ground on the lip when the drill is sharpened. This means that the drill may self feed in soft metals if there is not enough resistance in the cut to overcome this tendency, as in the case of drilling .011 per side. The solution is to grind the lip with a zero degree hook angle which makes it a scraper instead of a cutter. Hold the drill with the lip more or less vertical and touch the cutting edge inside the flute to the right side of your grinding wheel (the flat face). It won't take very many sparks to accomplish this. The flat you ground along the lip, on the spiraling surface of the flute, need only be about 1/64" wide to be effective. In fact since you are only drilling .011 of material per side the flat need not be ground all the way to the center of the drill but might only be 1/16" long or so. Then the drill could still be used as before for all other materials because so little of the cutting lip has been changed. In essence, you have slightly "dulled" the lip which will be generating the chip, and you may drill without fear of "grabbiness".

Second alternative is a "straight flute chucking reamer" for about $14, but you already have the right size drill so go for it.

Re: Drilling aluminum question

#8

Re: All you need to do is modify the grind of the

Joe Donohue

>Thank you all for the input. I have had a good night's sleep to think about it and now to the shop to try out the suggestions.

Joe Donohue

Re: Drilling aluminum question

#9

Re: All you need to do is modify the grind of the

Joe Donohue

>It worked! I had to read Al's directions about 6 times before I could get my mind around it. If that didn't work I was ready to try the boring bar thing and other suggestions.

I ground back the hook angle, set up the drill in the headstock, braced the vicegrips against the tool rest and used the cone center to push. Very slowly with lots of lubrication. I had the lathe turning about 150 rpm. The first half inch or so was the trickiest.

Thanks again to all.

Joe Donohue


img