Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Oneway Bowl Steady Questions

Posts

Oneway Bowl Steady Questions

#1

Oneway Bowl Steady Questions

Bill Grumbine (Kutztown PA)

>Greetings all

I have just confirmed another demo, and one that is new for me, at least from the demo point of view. I have been asked to demonstrate how I make the tall thin natural edged bowls that I make from time to time - similar to the one below.


In the course of my correspondence, I mentioned that I would need a steady rest for the demo, since mine is built for the Poolewood. I actually have two possibilities of rests to use for this particular demo, but it got me to thinking...

If I had a Oneway bowl steady, I could add this demo to my list and be able to accomodate all, or at least most of the various lathes I encounter. At least, I think so. First, how many people here have one, use it, and find it to be worthwhile? Even better, has anyone here used it for tall vase type NE bowls, where there is lots of deep hollowing going on? Finally, how fast does this thing adjust to different lathe beds, swings, etc?

Thanks.

Bill

Re: Oneway Bowl Steady Questions

#2

Re: Oneway Bowl Steady Questions

Wally Dickerman in Arizona

>Hi Bill...I have the Oneway steady and like if very much. I find that it's easy to use and would be easy to adjust from one lathe to another. You may or may not need a different clamp block for use on different lathes. I've used it on fairly tall hollow forms, up to 14 inches or so, and find that it does the job just about as well as my old 3-wheel steady. It has the advantage of being able to be installed on the lathe without removing the tool rest or the tailstock.

I think that you'll like it.

Wally

Re: Oneway Bowl Steady Questions

#3

Re: I have a Oneway Bowl Steady...

Jamie Donaldson

>...for my Stubby, and the only modification required was the proper sized clamp lock-down plate to fit the width of the space between the bedways. Oneway already has a clamp plate selection available, and I would expect that most lathes could be accommodated at present. I do use it for deep hollowing with excellent support where it is needed, and it aids in agressive cutting that I wouldn't attempt without the added support. I also often apply a wrap of masking tape to reduce the possibility of roller tracks on the already sanded exterior of vessels.

Re: Oneway Bowl Steady Questions

#4

Re: I have a Oneway Bowl Steady...

Norm Smith in Nova Scotia

>Bill, I have 2 of the Oneway steadys and find them excellent. They can be adjusted quite quickly. I usually use only one but add the second on really big stuff.

Re: Oneway Bowl Steady Questions

#5

Re: Oneway Bowl Steady Questions

Bill Howatt

>I have one on my General-26020 and have used it a few times and like it. As mentioned, you need the correct block to fit the bed spacing. As for different spindle heights you just move it up and down the pole and clamp it in place by tightening the screw.

Like most things, reading the setup instructions the first time seemed a bit confusing but it really is obvious once you have done it once.

I also bought the spindle steady head for it which uses the same mount structure as the bowl steady. Easy to changeover.

Bill

Re: Oneway Bowl Steady Questions

#6

Dick Hines

Re: I have a Oneway Bowl Steady...

Dick Hines

>I also have one Bill. I use it on my PM3520. Not for bowls but for deep hollow forms. Works rather well.

Re: Oneway Bowl Steady Questions

#7

Re: Oneway Bowl Steady Questions

Bill Grumbine (Kutztown PA)

>Thanks for the replies everyone. I will probably end up buying one for the Vega and then worrying about extra clamping plates for other machines as the need arises. I can't see spending a bunch of money on extra plates just in case. And, this gives me a good excuse to buy a steady for the Vega!

Bill

Re: Oneway Bowl Steady Questions

#8

Re: Does Vega have a way of ....

Jamie Donaldson

>... attaching a bowl steady of their own design? Since the 2400 has no standard ways, I doubt that a Oneway will work unless they/someone makes a very tall post on which the wheel assembly could be mounted?

Re: Oneway Bowl Steady Questions

#9

Re: Does Vega have a way of ....

Bill Howatt

>The post with mounting plate is 13-3/4 inches high off the bed which means you could probably do a 26+" dia bowl based on this dimension alone.

Bill

Re: Oneway Bowl Steady Questions

#10

Bill - Buy a couple

Mark Kauder, Phenix City, AL

>Bill, I have two that I use on my Vega. They work for full diameter or the smallest diameter. I use the pair on all hollow forms, one on each side to capture the piece, or one on the backside. I stack one on the other, and leave them mounted on the lathe. When not in use, I can swing then out of the way on the backside.

Do not bother to buy the blocks. Buy yourself several carriage bolts of various lengths, and some thick cut washers of various widths that will span the common width of bed gaps, and then use the bolts and washers as needed for the various lathes you work on.

I built my own block for the Vega with a small strip of 1" cold rolled steel welded to the middle of a 2.5" Cut washer and a bolt welded to the washer. Face it, this is not a really high tech problem, and does not require a ton of pressure, something simple works. You certainly do not need a factory (espensive) solution.

I am up at the Southern States Symposium, but if you need some pictures, let me know.

Mark

Re: Oneway Bowl Steady Questions

#11

Re: Mark-I'm not sure from.....

Jamie Donaldson

>... your answer whether you were able to use the Oneway steady or that you fabricated your own? I was questioning whether the original Onway post was tall enough to use on the Vega 2400?

Re: Oneway Bowl Steady Questions

#12

Re: Bill - Buy a couple

Bill Grumbine (Kutztown PA)

>Thanks Mark! As soon as I saw your name I remembered seeing one on your lathe, but I did not remember the second. I bought one at Woodcraft on Saturday. Once I get it up and running (and the business card cools off a bit) I will have to look into a second. How do you keep them out of one another's way?

Bill