Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Bubble in the finish

Posts

Bubble in the finish

#1

Bubble in the finish

Bev Thomas

>I have had a problem develop when turning pens. After I take the pen off the lathe I sometimes have a bubble in the finish adjacent to the centre band. I use Lee Valley's Turner's Polish, which is a shellac based polish, and top it off with several coats of Liberon wax stick. It's very frustrating because it's not visible until the pen is removed from the lathe. I hope someone has some suggestions.

Thanks. Bev

Re: Bubble in the finish

#2

Re: Bubble in the finish

Russ Babbitt

>Would not think you could get air bubble with this type of finish. What is your technique? I would guess apply a small amount to the paper towel apply to the pen with the lathe turning. Friction heats up the finish to dry and then apply the wax stick friction melts the stick and excess is wiped off with a clean paper towel.

Re: Bubble in the finish

#3

Re: Bubble in the finish

Bev Thomas

>Sounds exactly like what I'm doing.

Re: Bubble in the finish

#4

Re: Bubble in the finish

Ed Heuslein

>Howdy Bev: Has to be something outside the box here. How about giving us a step-by-step of your finishing process starting with when you put down your tool (skew? ;>{ and pick up the first piece of sandpaper all the way to taking it off the lathe. Ed

Re: Bubble in the finish

#5

Brad Vietje

Re: Bubble in the finish

Brad Vietje

>Bev -- could you just be using too much ?

Would like to know more about the solar part ...

Safe spinning

Brad Vietje

Newbury, VT

Green Works Solar Store, Groton, VT

Re: Bubble in the finish

#6

Re: Bubble in the finish

Bev Thomas

>OK, step by step:

-once the turning is complete I start sanding with 120 grit. I wipe off the residue with a dry cloth between each grit.

-I progress through 180,220, 320.

-then I go back to 220, 320, and then 400

-then with the lathe turned off I sand with 400 going with the grain to remove the final scratch marks. (by the way, I have micro mesh on order)

-then with the lathe off I apply the first coat of polish going with the grain

-I turn on the lathe and buff with a clean dry cloth until the polish comes up

-I apply another coat of polish with the lathe on and buff until hardened

-I apply a total of 5 coats of polish

-I let it sit a few minutes before applying the wax

-with the lathe on, I apply the stick wax and using a clean dry cloth I buff back and forth

-I apply about 5 layers of wax and buff well between each

-it usually works well, but lately I've had these spots where it looks like the polish is not adhered to the wood. The bubbles are not soft and sticky, the polish is dry, and you can't see it until the pen is off the lathe.

I hope you can shed some light on this.

Thanks

Re: Bubble in the finish

#7

Re: Bubble in the finish

Bev Thomas

>Hi Brad,

That's a good point. I'll try pulling back on the amount of polish.

The solar part is our other passion! My husband and I built a home 4 years ago and we live totally off grid. We did about 7 years of research before taking the plunge (and once the kids moved out!) and it has been an awesome adventure (not to mention the learning curve). Now that the major part of building is done, we are taking some time to "play" and have discovered the fun of turning pens(mostly me) and building willow furniture (mostly my husband). I see you are in the solar busines as well!

Re: Bubble in the finish

#8

Re: Bubble in the finish

Ed Heuslein

>Howdy Bev: One thing I've learned about finishing over the years is that no matter what the turning is, and no matter who the turner is, the finishing methods are as numerous as the number of turners involved. Having said that, I first must admit that I have no experience with Lee Valley finishes. I have used a similar shellac based product, Hut Friction Polish, with good results. After initially sanding the blanks to 400g, I apply HUT PPP Brown to the bare wood and burn in in. This fills small voids. I then apply the friction polish with the lathe running very slow, a paper towel between my thumb and forefinger, and apply the polish, moving back and forth, never stopping. I turn up the speed and burn it in. I repeat this two or three times, depending on the wood. After waiting several minutes for it to dry good, I apply pure carnuba wax and burn it in in the same manner as the friction polish. Your fingers should get hot, but not burn a blister (DAMHIKT). Now, there are lots of other ways and I have no problem with any (well, most)of them.

I believe you are using too much polish and too much wax after the fact. The Liberon wax stick is really meant to be used on bare wood - it has some grit in it - similar to the Hut PPP sticks. All good products when used as intended I believe.

Now that I've stuck my neck out, chop it off folks!

Re: Bubble in the finish

#9

Re: Bubble in the finish

Bev Thomas

>Thanks Ed. Just to clarify, do you mean by 'burning it in' that you are buffing it until your fingers feel warm? Also, I wondered about using paper towel. You don't get fibers coming off onto your finish?

Bev