Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

No way to run a railroad. :(

Posts

No way to run a railroad. :(

#1

No way to run a railroad. :(

Allen Neighbors

>I got low on cutters, and decided to try some harder steel than M2. I also wanted to get the 3/16 Drill Rod for my toolrest edges. Placed an order with Wholesale Tool... Houston store... April 13th.

Have received the proverbial runaround three times on the phone. Still don't have my order. I'm out of 1/8" and 3/16" cutters and patience. I could have driven there and back in only 20 hours.

Does anyone know of a good place to order ground square toolbits in harder-than-M2 steel? (One where they have good service?)

Re: No way to run a railroad. :(

#2

Re: No way to run a railroad. :( *LINK*

nailshooter

>Allen:

Although this discussion was on M2, many of the suppliers listed here certainly have other steels. There are some good thoughts on alternative steels and bits, too.

I am buying 3/16" X 3" square M2 with 5% or 10% (they are lasting so long I don't remember what I bought last) cobalt from a local machine supply shop for about $1.75 each. I do have to cut them with a grinder, but I go veeery slow and keep them really cool (as per instructions of supplier) and don't bother with a retemper.

Robert


Steel discussion and links

Re: No way to run a railroad. :(

#3

Re: Hunt for Rex 95

Al Crandall (N.E. of Indy)

>Crucible Steel makes the Rex series of tool steels, of which I have a strong preference for Rex 95. Do a google search for Rex 95 and open the first hit. I have made hundreds of miles of chips in prehardened mold steel using these bits in the boring bars. For boring in tough steels and for use in a shaper I never found a steel which held an edge better than the Rex 95 bits. I've got to wonder just how hard is the wood you are turning?

Sorry to hear about your bad experience with WT. I have bought a lot of stuff from the Indianapolis store, and always got service of one week or less on any item which was out of stock. My 2 1/2" die stock was shipped from the Texas store to Indy in less than one week.

Re: No way to run a railroad. :(

#5

Ditto - Go ENCO

Mark Mandell - Gone Round In Jersey

>Where I buy ALL my drill rod and tool bits (cutters) there. They stock up to 10% cobalt which translates to M-45.

You can go to McMaster-Car, Catalogue page 2473, for some fairly exotic cutters, but you WILL pay for them.

Both places have very good service.

mm

Re: No way to run a railroad. :(

#6

My favorite source  *LINK*

Brian Hahn in SW Wisconsin

>


McMaster-Carr

Re: No way to run a railroad. :(

#7

Re: No way to run a railroad. :(

Allen Neighbors

>Thanks for the advice, Folks, I placed my order with ENCO just now.

And will call the other guys, and if it hasn't shipped already, I'll cancel it.

Appreciate the help.

Re: No way to run a railroad. :(

#8

Re: My favorite source

Bob Fawcett

>I have had orders from these guys arrie in 2 days or less and this was with regular shipping.

Re: No way to run a railroad. :(

#9

Re: Suggested supplier of HSS *LINK*

Russ Fairfield

>Here is the link to the supplier I use for M2 and cobalt tool steel. Get the Series-132 in 10% cobalt. This is inported steel, but the price is right, their service is good, and I have used it for years for cutting both steel and wood without any problems.


http://www.industrialboys.com/columnar.aspx?cat_id=1543&session_id=667627629&category_site=STARTOOL

Re: No way to run a railroad. :(

#10

Re:These small high alloy bits are....

Jamie Donaldson

>... easily cut with a Dremel cut-off disc, and you don't have to be concerned with affecting the hardness in any way. Stick the bit stock in a vise, ring with the Dremel disc, and whack with a hammer! Just make sure the floor isn't covered with shavings when the hammer blow sends the bit flying across the shop- don't ask how I know this!!

Re: No way to run a railroad. :(

#11

ENCO

robert davis

>

Re: No way to run a railroad. :(

#12

Re:I don't usually cut them...

Allen Neighbors

>all my tool bars have deep enough holes to allow a new bit to stick out about 1/2" to 3/4", depending on the size of the cutter. The curved bars are a different story... these I use a shorter cutter in.

I do have to shorten the 1/8" cutters, because I don't want so much sticking out of the toolbar.