Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Green Poplar Droplet 5224

Posts

Green Poplar Droplet 5224

#1

Green Poplar Droplet 5224

Bruce Forrest

>This is another droplet-shaped, hollow-from-the-bottom form. It is about 9 3/4 inches tall. If the red one was "Terran" then this should be "Vulcan", but it reminds me more of the ocean.

All commments welcome.


img

Re: Green Poplar Droplet 5224

#2

ebd

Re: Green Poplar Droplet 5224

ebd

>Very, very, very pretty. I bet this one blows peoples minds when they pick it up. Looking at the picture I would have sworne either ceramic or glass. How in the world did you hollow through thet tiny hole?

Re: Green Poplar Droplet 5224

#3

Re: Green Poplar Droplet 5224

Tommy Holmes

>Absolutely gorgeous! Unbelievable finish. I have seen others of yours and am in awe. I also like that you leave the voids and do not try to fill them.

Where does the brown come from? Are you highlighting with it or is it naturally occuring? What type dye are you using? Is there somewhere to find out about the bottom hollowing?

Re: Green Poplar Droplet 5224

#4

Re: Green Poplar Droplet 5224

Bruce Forrest

>Thanks for the comments.

The variations in color are a result of the wood.-partly spalted poplar.

The dye is water soluble aniline dye.-a mix of blue and green actually. Poplar will give more variations in color than ash, for example, because of the different colours in the poplar and the fact that different parts absorb the dye differently.

As far as hollowing through the bottom is concerned, I pick a blank 3 or 4 inches longer than the finished piece and mount it in a chuck. Then I turn so that the bottom of the piece is on the right. I turn the shape of most of the piece (leaving what will be the top thicker than it will eventually be to retain some strength.) Then I hollow it out and dry (microwave).

Then it's remounted and finish turned. Then I cut off the piece with enough material to finish the top.

The "stub" of 3 or four inches left in the chuck is what I use to form the plug. I just get it to proper size and then glue on the hollowed piece. Now it's in a "normal" configuration with a tenon on the bottom. Then finish shaping the rest of the top part. Easier than it sounds.

Re: Green Poplar Droplet 5224

#5

Re: Venusian?

Winnemucca Lynn

>

Re: Green Poplar Droplet 5224

#6

Re: Green Poplar Droplet 5224

Tommy Holmes

>It makes sense to think about it for a minute. Thanks for the info.

Re: Green Poplar Droplet 5224

#7

Steven Antonucci

This would make a great article for WoodCentral

steve antonucci

>Don't you love how I'm volunteering you for some work? ;-)

I really like these. Great form and finish. Conceptually, I get it, but I think a few pictures would clear up any remaining questions. (such as how do you hollow the top after reversing, holding methods...)

Thanks for sharing.

Steve

Re: Green Poplar Droplet 5224

#8

Re: Green Poplar Droplet 5224

Bruce Forrest

>Thanks everyone for the responses so far. In this piece, all of the actual hollowing is done from the bottom. Most of it is fairly standard, using a boring bar with laser and a steady rest. Then at the bottom of the hole (which is the top of the finished vessel), it gets a little trickier. I draw the final shape of the outside on the piece and hollow down to a point which is roughly 3/4 inch from what will be the top of the piece. The last 3/4 inch is exceedingly narrow as you can see. After the piece has been cut off, and reglued on the tenon exposing what will be the top of the finished piece, the outside of the top is shaped using the guidelines drawn on to guide the hollowing. Then it's a simple matter to use a 3/16 bit to drill the 3/4 inch to connect with the hollow inside. The tenon is removed using a vacuum chuck. All the rest is with a stronghold.