Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Thinning Epoxy

Posts

Thinning Epoxy

#1

Thinning Epoxy

Bill Crommett

>To those that have used epoxy extensively perhaps you can give me some guidelines as to what proceedures to use to thin epoxy to a consistency to use as a weatherproof finish for an outdoor project. I would like to thin the epoxy enough so that it would soak into the wood grain instead of staying on the surface.

Re: Thinning Epoxy

#2

Ellis Walentine

Re: Thinning Epoxy

Ellis Walentine

>I wouldn't recommend thinning epoxy, but that's not to say it can't be done. (We'd need an epoxy authority to weigh in on that.) From my experience with gates and other outdoor epoxy projects though I've picked up that epoxy itself is not at all immune to UV degradtion. If you intend to create an epoxy surface, whether in the wood or on top of it, you had better figure on applying a coat of varnish of some sort to protect the epoxy.

I'll be most happy to hear more testimony pro or con.

Ellis

Re: Thinning Epoxy

#3

Re: Thinning Epoxy

Bill Crommett

>Good thought. I hope my Sikkens hasn't gone bad. Thanks

Re: Thinning Epoxy

#4

Re: Thinning Epoxy

Brian Hahn in SW Wisconsin

>Ellis is right about epoxy needing UV protection for outdoor use. Boat builders use spar varnish. But be careful here because not all varnishes are compatible with epoxy. Check the epoxy manufacturers literature for more details. System 3 has a lot of information on their web site.

If you want better penetration, it is much better to choose an epoxy with a lower viscosity (more fluid). I've got System 3 epoxies that range from a syrup-like consistency to one that is almost as runny as water.

Re: Thinning Epoxy

#5

Re: Thinning Epoxy

Mike Cunningham (Cape May)

>Hi Bill,

I use it on boat restoration projects. My most recent was a 1962 Whaler, all mahogany console and reversible pilot seat. I mix the usual 2:1 and apply it with a short nap roller. It soaks in just fine. I've never attempted thinning though I've altered the ratio a bit but not much. I then apply varnish. I use Epiphanes. On the Whaler I applied 12 coats.

Anyway, I'd say go with 2:1 apply to clean wood and then a few coats of high quality varnish. Scuff and re-varnish every 2 or 3 years as needed, just stay ahead of it.

Mike

Re: Thinning Epoxy

#6

Re: Thinning Epoxy

Rick Allen

>There are three ways I can think of to thin epoxy. The first way is the best:

1. Use an epoxy which is thin when mixed and has a loooooooooong cure time.

2. Warm the wood, not the epoxy, warm epoxy is much thinner than cold epoxy. The BIG down side of this is that epoxy cures by heat. That heat is usually provided by the chemical reaction of the two parts of epoxy. That is why heating the wood, not the epoxy will thin the epoxy without decreasing pot life.

3. Add alcohol to the epoxy. This is VERY iffy which makes many other variables more important. The alcohol has to evaporate off before the epoxy finishes "cooking". To much alcohol, to cold, high humidity, poor ventilation, to dark, to light.

So back to option 1:

There are several epoxies which are well suited to deep penetration. Look for products like "Git-Rot" or "CPES" which are designed to treat wood rot.

You still need a finish on the wood. Epoxy will stop the transfer of moisture. But epoxy does nothing to protect the wood from UV.

Re: Thinning Epoxy

#7

Re: Mike-question? If you are.....

Jamie Donaldson

>....going to apply 10~12 coats of varnish, why bother to use epoxy at all?

Re: Thinning Epoxy

#8

Because

Mike Cunningham (Cape May)

>Because I'm a glutten for lots of stripping, varnishing, sanding and other forms of punishment!

Seriously, I've been told that the epoxy will not stand up to UV and needs varnish as a protective coat. As well, I've been told that varnish alone needs the "undercoat" of epoxy to truly protect the wood outdoors, particularly in a saltwater environment.

The number of varnish coats was to provide depth to the finish, a high quality appearance. I could certainly have gotten away with less, if I were looking for protection only.

Reading various manufactuers text and talking to wood boat guys around here, an old boat building area, regarding wood boat restoration is where I've found this info.

The console on the whaler is mahogany and was coated with several layers of paint. It required a tremendous amount of time and elbow grease to bring it back to a state that I was satisfied with. The reversible pilot seat was gone so I obtained plans and built one of solid mahogany. After all of that, I'd decided it best "err" on the side of overkill, plus I wanted that deep finish that I mentioned.

From West Epoxy:

The function of a finish coating like paint or varnish over an epoxy barrier coat, is to decorate the surface and protect the epoxy from sunlight. In doing so, the finish coating extends the life of the epoxy moisture barrier, which, in turn provides a stable base that extends the life of the finish coating. Together the two form a protective system far more durable than either coating by itself.

Protection from sunlight is a primary consideration in the selection of a finish coating. Long term UV (ultraviolet) protection of the barrier coat depends on how well the finish coating itself resists UV and keeps its pigments, or its shield of UV filters on the surface of the epoxy barrier coat. A high gloss finish reflects a higher proportion of the light hitting the surface than a dull surface. All other thing being equal, a white (especially a glossy white) coating will last the longest.

Most types of coatings are compatible with epoxy. Thoroughly cured epoxy is an almost completely inert hard plastic. This means most paint solvents will not soften, swell or react with it. However, it is still a good idea to build a test panel to assure coating compatibility.

Re: Thinning Epoxy

#9

Re: Thinning Epoxy

Keith Newton

>Bill, while you can thin epoxy, I like to get the thin epoxy from the supplier. There are a number of sources, but the price is too high at most of them for my liking. Here is the source that I use.

http://www.fgci.com/

Re: Thinning Epoxy

#10

No good for exteriors

Jorge Castaneda

>Bill,

epoxy degrade readily under UV, sometimes is used in boats mixed with a pigment that blocks the uv.

let's hope JL chimes in, he knows a lot about this.

Jorge

Re: Thinning Epoxy

#11

Re: No good for exteriors

Mike Cunningham (Cape May)

>Actually epoxy is the preferred method for boats. As I said, it needs to be topcoated with high quality varnish or paint.

Re: Thinning Epoxy

#12

Another good source *LINK*

Mike Cunningham (Cape May)

>Raka


Raka epoxy

Re: Thinning Epoxy

#13

Re: No good for exteriors

Bill Crommett

>I didn't expect a full tutorial on the subject, but now I know more than In ever expected about epoxies, varnishes, and UV protection. I would like to thank all who participated in my education, and again testify as to what as great bunch here on this site.

To reciprocate, all I can offer is in regard to "How to treat women" .That is where I have made most of my mistakes and consequently have learned a whole bunch. Whoops, wrong website !

Re: Thinning Epoxy

#14

Re: Thinning Epoxy *LINK*

Brodie Brickey

>Here's a review of various clear epoxies. They address UV resistance, viscosity & a number of other issues.

http://www.oneoceankayaks.com/Epoxtest.htm

The boats are cool too..


http://www.oneoceankayaks.com/Epoxtest.htm

Re: Thinning Epoxy

#15

and also...

Brian Hahn in SW Wisconsin

>Epoxy becomes a structural skin, strengthening the surface and structure that it is applied to. Paint and varnish can't do that.

Re: Thinning Epoxy

#16

plus...

Brian Hahn in SW Wisconsin

>Several coats of epoxy form a waterproof barrier. This is especially nice for boats. Simple paints and varnishes can't do that.