Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

VFD Controller-long

Posts

VFD Controller-long

#1

VFD Controller-long

Don Orr

>I'm looking to the collective knowledge here which I know is expansive. I have a Jet 1642 EVS lathe with a Variable Frequency Drive controller. This lathe is sold as continuosly variable speed from 0-3200 RPM. My problem is my lathe will not run below 125 RPM. A good friend who works with these controllers on his job came over to see if he could figure it out. We found that the lower frequency limit was set at 5 Hz, instead of 1Hz which should allow the motor to run much slower. We were not able to adjust the parameters because the programs were locked and need a password to unlock. I called JET Tech Support and told them all this. They said 125RPM was as low as this lathe should run (even though marketed differently). I asked if we could adjust the parameters down to 1Hz to see if made any difference. He said we could but it might affect the long term operation of the motor. He did give me a password to unlock the programs though. Before we go messing with this, does it sound like something that would be harmful to the motor? Are there any cautions I need to be aware of? I know there are some electronic wizards that hopefully can shed some insight on this.

The lathe is not under warranty anymore and I have not had a single problem with it. I want to try spraying finish while the piece is turning slowly to reduce drips and runs. I know others do this and I think 125RPM might be too fast. (Although the guy I spoke with at JET said he sprays at his lowest speed of 500RPM.)

Thanks for any help,

Don

Re: VFD Controller-long

#2

Re: VFD Controller-long

jeff myroup

>Don,

I have the Jet 1642 EVS. I run the belt on the slow side pulley. I think it is 0-1200. My slowest speed is 50 rpm.

Jeff

Re: VFD Controller-long

#3

Re: VFD Controller-long

Bob Fawcett

>I don't think I would go much below the 5 hz. You get very close to DC when you do and motor windings on AC motors don't like DC.

As above make sure you are on the low speed pulley setup.

Re: VFD Controller-long

#4

Re: VFD Controller-long

Don Orr

>Thanks guys, I have tried that but am still wondering if that is too fast to spray a finish like lacquer. I was thinking more like 5 rpm.

Re: VFD Controller-long

#5

Re: VFD Controller-long

jeff myroup

>It might be to fast. I just turn it by hand and use very light coats of deft. They build pretty fast. I rub down between coats. I buy it in the spray can. If you are getting alot of drips and runs, I would suspect you are putting it on to thick.

Jeff

Re: VFD Controller-long

#6

Re: VFD Controller-long

Don Orr

>Thanks Jeff, you're probably right. I'm not the most patient when it comes to finishing.

Another question to follow this idea. How much if any sanding, cutting back, levelling is needed between coats ? Wet or dry sanding ?

Thanks again, very much appreciated.

Re: VFD Controller-long

#7

Re: VFD Controller-long

John Lucas

>Why not try using a seperate slow speed motor that you can drop in and out. I thought about doing that one time. I figured I would buy a geared slow speed motor and hook it up so I could simply run a belt from the motor pulley to the handwheel. Then tension from the motor would be enough to drive it. When I didn't need it I would simply pull the belt off and lay it aside. It wouldn't change any of the parameters of the lathe and you could drive it as slow as you want.

Many lathe motors have a good chance of overheating if you run them too slow for too long. That's why I considered the other motor in the first place.

Re: VFD Controller-long

#8

Re: VFD Controller-long

Jim Swank

>I would also be cautious about going below 5 Hz. See Bob's comment above about DC. As frequency decreases, the magnetic coupling of the wound stator (field) to the rotor (armature) becomes progessively less efficient. The motor runs hotter for the same current, and at the same time cooling is decreased becauuse the fan is turning slower. The motor may also experience an effect known as cogging (changes in speed) though that's unlikely to be significant in your application.

Re: VFD Controller-long

#9

Re: VFD Controller-long

Jimiles-Charlotte, NC

>I spray Deft from the can on 90% of my turnings. I spray at normal turning speed, 0000 steel wool inbetween, I will wait about 1 minute between coats. If you spray too heavy you will get runs. If you practice and give it a light quick pass you won't get runs. If you do get runs just sand/wool it off and try again. If you want a little more gloss, wax after last coat.

Re: VFD Controller-long

#10

Re: VFD Controller-long

Bob Fawcett

>Don,

5 rpm means 12 seconds to complete 1 revolution. You sit the turning on a table and walk around it that fast :-)

Re: VFD Controller-long

#11

I did that

Ron in Drums PA

>I did that on my 1236 for both slow and reverse sanding. Should work as well for spraying lacquer.

Re: VFD Controller-long

#12

Re: VFD Controller-long

Bill Crommett

>I mounted a piece of MDF on a lazy susn bearing and placed in front of my exaust fan. I just move the turntable by hand as I spray the lacquer. This also keeps the odor of the lacquer out of the shop.

Re: VFD Controller-long

#13

Re: VFD Controller-long

Brent at Robust

>Jim Swank is spot-on why they don't want you running below 5Hz.

The motor can overheat if left run for a long time, say more than an hour. Brent at Robust.

Good luck.