Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Kel Mcnaughton coring tool

Posts

Kel Mcnaughton coring tool

#1

Kel Mcnaughton coring tool

Ken

>Has anybody here used or saw this tool used on a HF lathe?If so how was it set up.

Thanks Ken

Re: Kel Mcnaughton coring tool

#2

Re: Kel Mcnaughton coring tool

Allen Neighbors

>I don't think the Harbor Freight lathes have a large enough motor. I've heard you shouldn't try the Kelton coring tool on less than 1-1/2 HP.

Re: Kel Mcnaughton coring tool

#3

Re: Kel Mcnaughton coring tool

Greg Haugen

>Craft Supplies says 1 horse minimum. I do have people though that core on a Jet 1236, very S-L-O-W-L-Y. I personally would not recommend it. There is alot of torque on the lathe when using one. HF lathes don't have the bearings to withstand it in my opinion.

Greg

Re: Kel Mcnaughton coring tool

#4

Re: Kel Mcnaughton coring tool

Ron in Drums PA

>I use it on a Jet 1236. It works fine, just maybe not as quick as a bigger lathe.

Re: Kel Mcnaughton coring tool

#5

Re: Kel Mcnaughton coring tool

Bill Grumbine (Kutztown PA)

>Ken, you might be able to do it, but you would need the patience of Job. I know of a couple of people who core on smaller motor lathes like Ron, but the HF is going to be pushing it. Perhaps if you could find a way to borrow a system before you buy. Then, there is the other option of buying it, and then having to upgrade your lathe! You might find out you need a new lathe anyway if you cook the motor or bearings.

Bill

Re: Kel Mcnaughton coring tool

#6

Re: Kel Mcnaughton coring tool

Denis Putland from Saskatchewan

>If you are thinking of spending the money for a coring tool then you have a very good reason to upgrade your lathe:):)

Hmm..?? perhaps getting the coring set up first would make the upgrade an absolute necessity.

When ever anybody does an upgrade they are all happier then a pig in ???? mud.

I know I sure was so happy with my lathe upgrade::::)))))))

Denis

Re: Kel Mcnaughton coring tool

#7

Re: Kel Mcnaughton coring tool *LINK*

Steve Russell

>Hello Ken,

While I have not turned on your specific HF lathe, I have cored thousands and thousands of bowls using the Kelton Center Saver (KCS). I wrote and article (link below) on using the KCS, which includes a section that details my innovative "Fluid Pulsed" technique for using the system on low HP lathes. While the process is slower on a small lathe, it CAN be done... I have done it many times on 1HP lathes and a few times on 3/4HP lathes. If you have specific questions, I would be happy to assist you. Take care and all the best to you and yours!


http://www.woodturningvideosplus.com/center-saver.html

Re: Kel Mcnaughton coring tool

#8

Re: Kel Mcnaughton coring tool

robo hippy

>Steve Russel's article has a lot of merit. You can core on a 1 hp lathe, but it isn't easy. The cutter on the standard set is about 3/8 inches wide. With the spear point, the shaving you remove is about

1/2 inch wide. If you can take a shaving that wide with a scraper, then you can core with it. The mini set from KM has a smaller cutter profile, and would be ideal for smaller lathes. The only problem here is that the tool rest sits a bit high for most 12 inch lathes, and the cutter does need to be at or slightly above center height. 1 inch above center is too high. One modification I made was to grind the point off so that the blade is square on the end. This results in a 3/8 inch wide shaving. It does not effect the cutting ability of the blade or how it tracks. I may have to try the concave thing on the face of the cutter some time.

robo hippy

Re: Kel Mcnaughton coring tool

#9

Re: Kel Mcnaughton coring tool

Ken

>Thanks for all the respones.I already have the coring tool,got it for Christmas.I got the HF at a good price on sale.I already have a 2hp motor lined up for a 150 bucks which still leaves me at at less than 4oo bucks for the whole setup.But my problem is getting it setup on the darn lathe.

Thanks Ken