Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Maple Bowl

Posts

Maple Bowl

#1

Maple Bowl

Gil Jones on Lake Seminole GA

>A slightly spalted Maple bowl with a small knurled band.

Deft lacquer and buffed. 7.5"wide by 3.5" hi and a 5/32" wall.

I really need to get those bowl buffs for the inside, do any of you use them (and like'em?).

Gil


img

Re: Maple Bowl

#2

Re: Maple Bowl

Norm Smith in Nova Scotia

>Gil, Very nice. love the textured band.

Norm

Re: Maple Bowl

#3

Barb Siddiqui

Re: Maple Bowl

Barb Siddiqui

>That's wonderful, Gil. Actually, I'm so new I'm acquiring all the necessities, and I bought the bowl buffs first; they're all I have for the inside and the outside. I bought a drill arbor and a plastic stand with a hose clamp to hold it, so the buffs are stationary and I hold the bowl against them, changing them out each time for polishing. It works well. Yes, I like them (the two inch.)

Re: Maple Bowl

#4

Re: Maple Bowl

Barry Elder

>Gil, I have the three and four inch bowl buffs and I have to be careful because they are recommended to spin at a higher speed and generate much more heat. But they do a knockout job!

Re: Maple Bowl

#5

Keith Tompkins

Re: Maple Bowl

keith tompkins

>Gil, that's a beautifully done job on the rim...it ties in perfectly. I'm impressed!

Re: Maple Bowl

#6

Bowls buff and lacquer

Dominic Greco in Richboro PA

>Gil,

You wrote:

"....Deft lacquer and buffed. 7.5"wide by 3.5" hi and a 5/32" wall. I really need to get those bowl buffs for the inside, do any of you use them (and like'em?)."

I have a set of the Beall bowl buffs. But I really don't use them as much. I bought a set of the small (3" or 4") wheels and end up using them most of the time. They do a good job on the inside of most bowls.

I notice that you mentioned that your finish is lacquer. However, I wouldn't use a buffing wheel to polish a lacquer finish. It's too easy to buff right through the lacquer (DAMHIKT)! The buffing wheels are more suited to oil finishes that are absorbed into the wood, rather than a lacquer finish that is built up and "sits on top" (I know that the fist couple coats of lacquer are somewhat absorbed. I'm just trying to make a point)

If you want to get a super glossy finish, I would recommend using automotive polish. 3M Finesse it, or Griot's Machine Polish work really well with lacquer. before applying them, I wet sand with Micromesh all the way up to 15000. Then I polish with Griot's Automotive Machine Polish, give it a coat of Renaissance wax and get a finish you can see yourself in!

See ya around,

Dominic

Re: Maple Bowl

#7

Really like that rim. Great work there Gil.

Craig Daymon

>

Re: Maple Bowl

#8

Brad Vietje

Ditto that ! Very nice bowl !

Brad Vietje

>

Re: Maple Bowl

#9

Thanks For All The Incouraging Coments and Ideas

Gil Jones on Lake Seminole GA

>I appreciate the info on the bowl buffs. Dom, except for my one-and-only dyed Red Hollow Form, my lacquer finish is mostly a tool to seal the wood, and does not build up on the wood. I buff with a 1hp Baldor buffer with 10" and 8" wheels left over from my gunsmithing days (so most any finish buildup is buffed off). I like polished wood. Here is a pic of my homemade knurling tool. The working part of it is a hardened steel drill bit guide bushing with a knurled flange (from a scope mounting jig). The guide bushing is mounted on a small bolt, and allowed to spin against the turning wood. I made it for this piece, and it needs a modification as it gets hot quick in use.

Gil


img

Re: Maple Bowl

#10

Re: Maple Bowl

Allen Neighbors

>Really nice work, Gil. Textured bead is beautiful. Good job!

(Got a beautiful box of wood in the mail today... Thanks! :o))))))))

Re: Maple Bowl

#11

Thanks, and have fun with the wood.

Gil Jones on Lake Seminole GA

>

Re: Maple Bowl

#12

Beale Buffs

Ron McKinley

>I have the Beale Bowl Buffs and run them at 3,000rpm on the lathe.....Ron

Re: Maple Bowl

#13

Re: Beale Buffs

Gil Jones on Lake Seminole GA

>No doubt I will get some bowl buffs, but 3000rpm seems a bit much in the friction department. Ron, what do you experience in the way of hot wood?

Re: Maple Bowl

#14

Re: Beale Buffs

Brian Hahn in SW Wisconsin

>A 4" buff running at 3000 rpm has the same surface speed as an 8" buff running at 1500 rpm.

Re: Maple Bowl

#15

Re: Beale Buffs *LINK*

Bob Fawcett

>Get one of these and you can run at any speed your lathe can operate.


Buffing adapter

Re: Maple Bowl

#16

Re: Maple Bowl

Ken Grunke from SW WI

>Gil, you're getting rave reviews on this bowl all over, and for a very good reason ;) What a great piece!

On buffing the inside of anything that's hard to get at, I've found that just using a hand-held cloth charged with white diamond compound works pretty good. Even with nothing but elbow power, in fact. Of course, holding it on a spinning surface works even better, if you can mount the bowl back on the lathe after finishing.

I find the disposable shop rags to be best, and safest. They'll just tear apart instead of grabbing your fingers if a catch happens.

Just briskly rub a folded up pad on the block of compound, all that's needed.

Re: Maple Bowl

#17

Re: Beale Buffs

Glenn Hodges, Nashville, GA

>Gil, I like that bowl. I use the bowl buffs all the time on the inside of mine at 1750 rpm. You have seen some of my work.

Re: Maple Bowl

#18

Re: Beale Buffs

Ron McKinley

>Heat is not a problem since I don't put much pressure on them. Beale recommends 3000rpm for the bowl buffs and 1700 for the flap wheels. I tried the bowl buffs at 1700 since I have a dedicated motor/set-up for that speed. In my view the bowl buffs didn't work well at the lower speed. On the other hand, John Lucas says they work even better at the lower speed and the piece is easier to control........Ron

Re: Maple Bowl

#19

Thanks. This is a great place to find ideas.

Gil Jones on Lake Seminole GA

>

Re: Maple Bowl

#20

Re: Thanks. This is a great place to find ideas.

Don in Central Illinois

>Can't help much yet, on how the 2" bowl buffs work, since I just received mine Tuesday and haven't been to the shop yet.