Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Blank for hook tool

Posts

Blank for hook tool

#1

Blank for hook tool

Robert D. Macgregor

>I was watching the instructions on making a hook tool from a hardened masonry nail and couldn't see how to keep the finished hook from rotating in the base without gluing it in (which would make it hard to replace). I wondered if the same process would work using an Allen wrench as a blank for the hook tool. This way, a very secure hexagonal socket (ie, an Allen nut) could be mounted on the tool handle that would allow easy changeover of homemade bits. The critical question is whether the steel in an Allen wrench is suitable for making small cutters.

BOB

Re: Blank for hook tool

#2

Re: Blank for hook tool

John Lucas

>Just grind a flat on the nail if needed. I use drill rod to demonstrate making a hook tool. I grind a slight flat and then install the tool in my bar with a set screw.

Re: Blank for hook tool

#3

Re: Blank for hook tool

Lan Brady

>Robert,

Flooring nails are square/rectanglular in shape.

Once shaped, I re-harden them but do not temper.

Lan

Re: Blank for hook tool

#4

Re: Blank for hook tool

Ralph

>Lan

Why not re-temper? Wouldn't it reduce the chance of braking the hook?

Re: Blank for hook tool

#5

Re: Blank for hook tool

Lan Brady

>Ralph,

For 3 dollars I bought a box of 250 nails.

I like making things and I can make these in about 5 minutes.

Ufortunately I have not had any to break by being too brittle.

I guess the hardness is just not at that level.

They are sharpened with a dremel tool, but it stays sharp for a long time as it is.

Maybe the metal guys can explain it?

Lan

Re: Blank for hook tool

#6

Re: Breaking the hook

Al Crandall (N.E. of Indy)

>Tempering the hardened steel to straw color, or by baking in your oven to 325 degrees, will only reduce the hardness by about 2 or maybe 3 Rockwell "C" points. This is not enough to alter the odds of total breakage in a hand held tool, but might be just enough to keep a really thin sharp cutting edge from breaking. Depending on your particular grind of the edge, I'd not worry about tempering until I saw small chunks leaving the cutting edge.

Re: Blank for hook tool

#7

Re: Breaking the hook

john lucas

>325 gives rockwell 62 on the last batch of drill rod I got from Enco. Most turning tools are tempered around 60 to 62 rockwell. One big difference between hook tools and ring tools is the hook tool is much easier to break. I do temper mine. The ring tool tends to clog more when hollowing green wood but the one I have cuts so well I use it more than the hook tool.

Re: Blank for hook tool

#8

Re: Breaking the hook

Robert D. Macgregor

>I'd prefer to make a ring tool rather than a hook, but I haven't seen instructions on how to make a ring... the hook looks pretty simple, though likely more fragile.

Re: Blank for hook tool

#9

Re: Robert, don't waste good ......

Jamie Donaldson

>.. turning time trying to make a ring tool when you can buy a Termite from Oneway. If you're really into making tools, buy just the Termite cutter and make a holder/shaft/handle to satisfy the tool maker urge, and end up with a satisfying hollowing tool that you can actually use!

Re: Blank for hook tool

#10

Re: Blank for hook tool

Russ Fairfield

>There was an excellent article on making and using a hook tool in the AAW Journal several years ago. Somebody with a collection of old issues might find it and provide you with a copy.

Re: Blank for hook tool

#11

Re: Breaking the hook

Lan Brady

>Al,

Thanks,

I knew there was a reason,

I just did not know why!

I hope all is well with you,

Lan