Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Gouge flute (long)

Posts

Gouge flute (long)

#1

Gouge flute (long)

Gordon Seto

>A detail gouge is not a spindle gouge that is sharpened to a steeper angle. The shape of the flute is different.

Having Doug Thompson (Thompson A-11 gouge) in the back yard, I got some gouge lesson 101.

He is the few if not the only gouge maker who makes 2 shapes of bowl gouges (�U� & �V�). That is where I want the collective wisdom of this forum.

As shown in the diagram (not to scale):

http://i118.photobucket.com/albums/o83/gbseto/Cross-sectiongougescopy-1.jpg

Spindle Gouge: about � of the steel is milled away. Therefore the gouge is not as strong as other gouges of the same bar size. The width of the flute is almost as wide as the diameter of the bar; it is easier to control.

Detail Gouge: only a small fraction of the gouge is milled away. Therefore there is still a lot of steel left underneath the flute. It is more rigid than spindle gouge of same bar size. It can be extended far beyond the toolrest without chattering. Usually they are sharpened to a steep angle; therefore they can reach into tight details. The width of the gouge is narrower, not as easy to control on long curve.

�U� shape Bowl Gouge: Obvious the bottom of the flute has wider radius, more open. They are supposed to be less likely to clog on wet wood.

�V� shape Bowl Gouge: Tighter radius on the bottom of the flute. Because of the smaller radius, when using the bottom of the gouge, the contact area is smaller. I find them cutting through dry wood easier.

The area I don�t quite understand is the difference between the 2 bowl gouges.

I have been to Doug�s workshop. He turns cowboy hats. His hat blanks were kept under water outside his garage. He said he uses the �V� shape bowl gouges exclusively; the �U� shape gouges are made upon the request of other turners. There is no doubt in my mind that he turns soaking wet wood. The gouges next to his lathe were all �V� flute bowl gouges. Several feet long shavings were everywhere. There was no sign of clogging.

I didn�t buy his bowl gouges because I already have Sorby, Crown, P&N, Oneway and Glasser gouges of various sizes. I am curious to find out the pros & cons of both gouge shape designs.

Gordon

Re: Gouge flute (long)

#3

Re: Gouge flute (long)

Barry Elder

>Gordon,

I purchased one of his V-shaped bowl gouges and it works so well I know I won't get one of the U-shaped gouges. The one I have cuts anything I put in front of it. It's almost disappointing to be able to rough out a bowl so quickly, whether the wood is wet or dry!

Re: Gouge flute (long)

#4

Re: You must realize Gordon, there...

Jamie Donaldson

>... is not a simple answer in this discussion! You already have the 2 profiles represented in your gouge collection. I look at the physical differences between the V and the U shaped flutes from a users point of view, and I prefer the U as found on Sorbys rather than the V found in Glaser and P&N gouges. The larger radius of the U exposes more cutting surface at the tip, and it's the profile I have used for the 22 yrs. I've been turning. It seems to allow a more uniform side grindable profile for the shape I grind on my gouges, a combination between Ellsworth and John Jordan grinds as I studied with both. The V shape has a more pointy tip, and for me the shape is not as efficient at cutting and evacuating shavings. Others will have the opposite opinion, and so I use what I prefer.

Re: Gouge flute (long)

#5

Richard Allen

Re: Gouge flute (long)

Richard Allen

>The bowl gouges I am mostly familiar with have the flute depth go beyond the middle of the bar stock. I have one bowl gouge which went by the name of Bowl Buster. The flute depth of this flute is less than half way through the bar stock.

The bowl gouges sold with the Glaser name are available with both "U" shaped flutes and "V" shaped flutes (oval).

A woodturning friend and I decided to test a bunch of bowl gouges. Some with "U" shaped flutes and some with "V" shaped flutes. What we found is that we could more easily detect the sharpness of the tool than the shape of the flute.

For my particular style of bowl turning "V" or "U" works the same.

I tend to use old Glaser bowl gouges more and non-Glaser bowl gouges. Those Glaser bowl gouges have a "V" shaped flute.

A "V" shaped flute tends to maintain a little more steel in the flute portion of the tool which should make for a stiffer toll that would permit more tool overhang. I think in actual use the stiffness difference would be difficult to detect.