Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

New 12 x 18 Jet Mini.....

Posts

New 12 x 18 Jet Mini.....

#1

New 12 x 18 Jet Mini.....

Wally Dickerman in Arizona

>While at the local Woodcraft today I examined the new Jet mini. 12 inch swing, 18 inches between centers. The motor is 3/4 HP. It has a wider, heavier bed, an index with spindle lock and comes with 2 toolrests, a 6 incher and a 10 incher. Sadly, the toolrest shaft is still only 5/8-inch. The price? A surprising $299. In my opinion, a very good lathe at that low price. I assume that a variable speed version will follow.

Wally

Re: New 12 x 18 Jet Mini.....

#2

Guess I could transfer

Don Henthorn

>my dc motor and control from my 10" Jet mini and sell my mini for close to what the 12" is selling for. Gee???? Should I go for it? What a quandry.

Re: New 12 x 18 Jet Mini.....

#3

Re: New 12 x 18 Jet Mini.....

Nelson

>Wally it must be the Arizona heat and the Jet lathe got shorter!! Bought one and its 20in. long.

Re: New 12 x 18 Jet Mini.....

#4

Steve Kubien

Metric version?

Steve Kubien

>For those of us north of the border? Maybe Wally was looking at one destined for here?

Steve Kubien

Ajax, Ontario

Re: New 12 x 18 Jet Mini.....

#5

Re: Metric version?

Wally Dickerman in Arizona

>We measured it and with both centers in place and it measured 18 1/2 inches. You might have trouble installing a 20 inch spindle to turn. Or maybe this one came out of the factory back door?

Wally

Re: New 12 x 18 Jet Mini.....

#6

I'll bet it was 20"...

Gary Evans Tallassee, TN

>before the centers were put in place. Can you imagine? The marketing guys actually exagerrated!

Gary

Re: New 12 x 18 Jet Mini.....

#7

Re: New 12 x 18 Jet Mini.....

Wally Dickerman in Arizona

>This would be a lathe that I would consider for a second, transportable lathe, except for the 5/8 inch toolrest post. I consider that a major flaw. Especially for a lathe that swings 12 inches. An inexpensive aftermarket banjo to accommodate a 1 inch post might be the answer.

Wally

Re: New 12 x 18 Jet Mini.....

#8

Re: New 12 x 18 Jet Mini.....

John Lucas

>Even my Nova comet had a 3/4" post.

Re: New 12 x 18 Jet Mini.....

#9

Re: New 12 x 18 Jet Mini.....

Brodie Brickey

>I agree the tool post should be larger. It sounds like they are using standardized parts from the regular Jet mini and its 10" swing. Bed is probably the same, etc. How is the tailstock? Does it look like they welded on a 1" plate to make it taller or is it significantly different?

Brodie

Re: New 12 x 18 Jet Mini.....

#10

Re: New 12 x 18 Jet Mini.....

Wally Dickerman in Arizona

>The bed is wider and heavier. The tailstock is made to fit the new bed. In my brief examination the Banjo and toolrest was the only glaring fault that I found. Using a 10 inch toolrest with a 5/8 inch post will cause problems. This sort of mistake convinces me that lathe design engineers usually aren't turners.

Wally