Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

fiber optic light help please

Posts

fiber optic light help please

#1

fiber optic light help please

ken chase

>I have seen a plan for a home made fiber optic light to use in thinwall hollowforms. The information that was not provided was exactly what kind of fiber to purchase and where.

It also didn't show if there was some kind of bulb on the end of the cable that emitted the light. I'm totally ignorant on this subject and would appreciate any information on how to build this kind of device. I know I can purchase a unit for about $400.00 but the plan suggested an outlay of under $100.00.

Thanks

Ken Chase

Re: fiber optic light help please

#2

Re: fiber optic light help please

John Lucas

>Ken I can't help you much. There is a light at the end of the cable, otherwise it wouldn't work. I looked into fiber optics but the only cables I could find were really expensive. I may not have found the right sources, and I'm sure the price has come down.

I've been using the automotive tail light bulb with a 12 volt transformer. I use a small flashlight with a small bulb on flexible arm for really small work.

Re: fiber optic light help please

#3

Leo Van Der Loo

I do have a fibre optic light, it was a ring light *LINK*

Leo Van Der Loo

>used with used with a microscope, company went with a different setup and these where disposed of.

However you probably aren't able to get one of those, but look on the net, you never know.

Herman De Vries has a write-up with pictures of a setup he made, and it also gives sources for parts.

Go to tools and tips on his site, and you'll find it easily.

Have fun and take care

Leo Van Der Loo


http://www.hdv.net/

Re: fiber optic light help please

#4

Try new White Leds

Mike Brazeau

>I corresponded with Herm DeVries a few months back and he said that he found the light source he used could be improved upon. I am reposting what I posted at WoW to your question. For a few bucks you can make it. These small flashlights are very bright and battery life for AA's is measured in hundreds of hours. It can be powered with one single battery, although it uses two in the flashlight and is somewhat brighter at 3 volts.

"Recently I emailed back and forth with Herm about his Fiber Optic system and he mentioned LED's as a possibility. Individual white LEDs to buy them are quite expensive. I had a couple of $6 5 LED flashlites from Princess Auto. One did not work so I was able to determine that the LED's in it were good and that it was a switch problem. I cut the thing apart and extracted the white LED pack, soldered a wire to it and tested with a battery. The assembly is just over 1/2" in diameter and can easily be attached to a boring bar. I am going to connect to a DC power pack and don't see why it shouldn't stand up to the rigours of hollowing. I am also going to protect it with the protective cap that comes on a spray bottle of insect repellant when you buy it. "


img

Re: fiber optic light help please

#5

Re: Try new White Leds

ken chase

>Thanks. I hope I don't come off as stupid but I'm confused. Is your recommendation to go with an led light instead of fiber optic or to use on the end of a fiber optic cable? I really don't have any aptitude toward electronics or related subjects. I do, however, want to make the box Herm describes. Even though he suggests a pool supply I haven't figured out exactly what to ask for when I call a pool supplier. Appreciate your help as well as others who responded.

Ken

Re: fiber optic light help please

#6

Re: fiber optic light help please

Curly Smith

>I'm probably way off base but perhaps something along the lines of this would be useful:

Flashlight, 7" Fiber Optic Wand


If you just want to play with, and learn about, fiber optics then you can learn and build the above with either of these kits:

Fiber Optic Kits

Fiber Optic Light Kits

FYI - you do need a light source. Fiber optic cable is nothing but glass threads. If you put light a one end then it will come out the other end.

Re: fiber optic light help please

#7

Re: Try new White Leds

Mike Brazeau

>Hi Ken.

No fibre optics would be used at all. This setup would be the same as those using a taillight bulb that were detailed at WoW, but you do not have to worry about the filament disintegrating due to vibration, which was the biggest drawback of that system. The 5 LED pack (any similar pack could be used, some have 4 LED's) would be taped to the boring bar, perhaps 2-4" back from the cutter. The wire soldered to it would be taped to the bar and taken back to a 3 volt Direct current power supply or perhaps a couple of D cell batteries with a single pole switch in the circuit. I used some 16 gauge lamp cord because it was what I had, but it could be much smaller gauge than that. The LED's have to be connected to the correct polarity of the battery or DC power pack since they are diodes, but that is easily determined. They work one way and don't the other. I have been going to do a more complete writeup on it, but haven't got to it yet. I have attached another shot I had taken of the connection to the LED pack. The red portion is the piece of the flashlight I cut off to access the LED's. Perhaps I could browse a Radio Shack site and come up with some part numbers. This would be an excellent introductory electronics project for anyone! A store like Harbour Freight in the US probably has these LED flashlights.


img

Re: fiber optic light help please

#8

Re: fiber optic light help please

Eddie Pacheco, San Jose, Ca.

>Hi, I would like to have the link to the fiber optic article that you mentioned. I think I may be able to find a source for fiber bundles. The cost of them may be the problem.

Re: fiber optic light help please

#9

Dick Hines

Re: fiber optic light help please

Dick Hines

>Why not get a laser attachment for your hollowing tool? You don't say what sistem hollowing tool you are useing but most or all can be fitted with a laser.

I have a Kelton and a Jamieson systems and they both have lasers.

Re: fiber optic light help please

#10

Re: Try new White Leds

Dinyar Chavda

>http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=93712

4" NINE LED MINI FLASHLIGHT at Harbor Freight currently on sale for 4.99 (US).

I guess this would work.

Re: fiber optic light help please

#11

Re: Try new White Leds

Dinyar Chavda

>On 2nd thought, I wonder if a 13 LED setup would have too large a diameter to be useful.

Re: fiber optic light help please

#12

Leo Van Der Loo

Re: Try new White Leds *LINK*

Leo Van Der Loo

>Hi Ken

Yes you could go with the light emitting diodes, but you'll need a bigger opening for that than the fiber optic wire.

I got a link here to a place that sells the jacketed multi strand fiber optic wire, and sell them by the foot length or by the roll. I'm sure there are more places that sell them.

Herm used 2 bundles of 30 strands I think, but doesn't tell how thick each strand is.

Thicker strands are stiffer but have more surface area for light in/output, you'll have to decide which you want, these people do have 50 strand 1/2mm thick for instance, and you could use 2 wires if one was not enough.

Have fun and take care

Leo Van Der Loo


http://www.fiberopticproducts.com/Jacketed.htm

Re: fiber optic light help please

#13

Here are the plans...... *LINK*

Russ Babbitt

>Look under "Tools and Tip" and scan down the page for plans.


Herman de Vries

Re: fiber optic light help please

#14

Inspection Light

Curly Smith

>I finally recalled the term "inspection light" and a google search gives these as some of the results:

Fiber Optic Flashlight Adapter

Comes in 7" and 20" versions (20" $10)

3 in 1 Flexible LED Inspection Light $8

Coast 19.5in. Flex Flashlight-360� Flexible Neck $36

If the above won't yield enough light then you can do as Leo suggests and buy some jacketed cable from

Jacketed cable but I'd be tempted to add the

FO-08 Spotlight . . . $8.50 to focus the light. You'd still need a bright light source - maybe a small halogen if you had a way to handle the heat.

Re: fiber optic light help please

#15

Re: Try new White Leds

Jorge Castaneda

>Mike,

I think it is a good idea, but not atacched to the cutter, if you make a mess of shavings and that takes only seconds, you will have a hard time to witdraw the tool, so a pattern of cut, eject and then inspect with the light would be more like it, and the opening can remain smaller.

I have a mini flash light with only one led in a goosneck and that is what I am using so far.

Re: fiber optic light help please

#16

Re: Try new White Leds

john lucas

>The light coming from the end of fiber obtics doesn't spread as good as a light bulb. I would guess you have to sort of aim it at the side by bending it. I use a large bundle at work, about 1/4" in diameter. I think replacement cables of that stuff runs about $150. It won't bend very well for aiming purposes. The thinner stuff would probably bend better.

The big advantage is that you can put really bright bulbs on the other end. We use a 150 watt quartz light at work and it produces a very bright light which might make it easier to light up woods that have dark areas.

Re: fiber optic light help please

#17

Killer website, Leo. Thanks!

Eddie Pacheco, San Jose, Ca.

>