Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Vicmarc clone *LINK*

Posts

Vicmarc clone *LINK*

#1

Vicmarc clone *LINK*

Mike Cunningham (Cape May)

>Could someone tell me if this chuck is the Vicmarc clone and do the Vicmarc jaws fit this chuck!

Thanks

Mike


Grizzly chuck

Re: Vicmarc clone *LINK*

#2

Re: Vicmarc clone

Gary in Zirconia, NC

>Yes, that's the one.

Re: Vicmarc clone *LINK*

#3

Re: Vicmarc clone

Bill Clark

>Yes, it's a clone. But it's not the quality of the Vicmark. I ordered one and tried it out. The one I got did not run true. I tried different jaws I ordered with it and it still did not center properly. The jaws had a lot of play inside the chuck. I sent mine back (read the small print, Grizzly has a high restocking charge in addition to you paying return shipping). The Australian made Vicmark is simply better quality than the Chinese made clone. Some have reported they were happy the their clone. I was not.

Re: Vicmarc clone *LINK*

#4

Re: Yes, but......

Russ Fairfield

>There always seems to be a "but" with these clones.

The Vicmarc jaws could be used on the only Grizzly chuck I have seen, but only one of the screws lined up with the base jaw. The other screw was close enough that drilling out the hole in the jaw to a larger diameter would have allowed both screws ro be used. I have been told by others that the Vicmarc chuck jaws did fit their Grizzly without any problems and they could use both screws.

Re: Vicmarc clone *LINK*

#5

Acceptable

Gil Jones on Lake Seminole GA

>I have a VicMarc 100, and a Grizzly H6265 (plus two extra Grizzly jaw sets). All VicMarc and Grizzly jaw sets interchange with no problems. While the VicMarc seems to be made to higher quality standards, and is smoother operating, the Grizzly is acceptable at its cost point (as are the Grizzly jaw sets). I have not found any problem with either chuck running less than true. The T-handled hex wrenches (3mm and 8mm) on the Grizzly were so undersized as to be unusable, and Grizzly sent me a usable set (on the second try). Would I buy a Grizzly chuck again, yep, and I may well buy another one just because they are handy to have, and at half the cost.

Gil

Re: Vicmarc clone *LINK*

#6

Thanks

Mike Cunningham (Cape May)

>A few members are looking at chucks and wondered about the Grizzly, hence my question. Seems as though the old adage is correct "If it sounds too good to be true..........". This chuck sounds like many Grizzly products, as they relate to quality control, some are just fine, some are not.

Thanks,

Mike

Re: Vicmarc clone *LINK*

#7

Re: Vicmarc clone *LINK

Steve Harder

>Here's a link to a Grizzly chuck tuneup. This was the first thing that I did after I unpacked my Grizzly and it's smooth as silk.

http://www.theturnersshop.com/turning/h6267/h6267-1.html

Re: Vicmarc clone *LINK*

#8

Re: Vicmarc clone *LINK

Bill Crommett

>That link didn't work.

Re: Vicmarc clone *LINK*

#9

It worked for me

Gary in Zirconia, NC

>

Re: Vicmarc clone *LINK*

#10

Re: Vicmarc clone *LINK

Mike Cunningham (Cape May)

>Very interesting tutorial, looks easy enough to do. I like your site as well.

Thanks,

Mike

Re: Vicmarc clone *LINK*

#11

Dynamite Web Site!

Clem Wixted, Jonesboro, AR

>Steve,

You have some great stuff on your site, thanks for sharing.

Clem