Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

Tool rest for Jet Mini

Posts

Tool rest for Jet Mini

#1

Tool rest for Jet Mini

Joe in a Cleveland suburb

>Hi.

Where can I get a longer than stock tool rest for my mini? The one that came with it is too short. I am currently using the bed extension (is that the correct term) trying to make table legs.

Thanks.

Joe

Re: Tool rest for Jet Mini

#2

Re: Tool rest for Jet Mini *LINK*

Bob Fawcett

>Best Wood Tools makes a modular tool rest system and they a post to fit your mini. Lots of choices.


Best Wood Tools

Re: Tool rest for Jet Mini

#3

Re: Tool rest for Jet Mini

John Lucas

>I bought the offset tool rest from Best Wood Tools. It's my most used tool rest.

Re: Tool rest for Jet Mini

#4

Re: Tool rest for Jet Mini

Ralph

>Penn State Industries also has tool rests that will fit the Jet/Delta mini's

Re: Tool rest for Jet Mini

#5

Re: Tool rest for Jet Mini

Matt Berry

>The best wood rest can also be found at packard woodworks along with a few other rests.

One other option is to by a rest from monster-tool, their website is

http://www.monster-wood-tool.com/

Re: Tool rest for Jet Mini

#6

Re: Tool rest for Jet Mini

Craig Daymon

>Lee Valley, and a few other places, sell the Sorby modular toolrest set, which is similar to the one sold by Best Wood Tools. I have it on my mini.

-Craig

Re: Tool rest for Jet Mini

#7

Re: Tool rest for Jet Mini

Bill Crommett

>Bestwoods makes great tools, but when I needed a longer tool rest for my Jet mini I went to the steel store and bought a couple of feet of 5/8 in cold rolled steel and welded up a tool rest for myself. It doesn't look too pretty, because I am a shaky welder, but it held together and is quite funtional. Cheaper, roo !

Re: Tool rest for Jet Mini

#8

Re: Tool rest for Jet Mini

Leppikallio

>However I think you should remember that the banjo isn't that big in these mini lathes so you would also need second banjo for Long toolrest.

However I think that if you don't use long toolrest that much you could make one wooden version and play with it? And also that "second banjo".

In fact this idea is not mine, I'm sure I have seen it somewhere just don't remember where...

Re: Tool rest for Jet Mini

#9

Re: Tool rest for Jet Mini

Joe in a Cleveland suburb

>I thought about that. Seems too simple. However, I don't have welding equipment.

Thanks.

Joe

Re: Tool rest for Jet Mini

#10

Re: Tool rest for Jet Mini

Joe in a Cleveland suburb

>Monster doesn't seem to have anything longer than 6"

Joe

Re: Tool rest for Jet Mini

#11

Re: Tool rest for Jet Mini

John Lucas

>You are correct about the length. I'm not sure I would put something 12" long on that banjo. For spindles it would probably be safe but if you turned something bigger and got out on the end you could be asking for problems. That being said I have the offset tool rest which hangs out 6" on one side and I haven't had any problems. I haven't had any bad catches either so I 'm not sure that's a definitive answer.

I plan to make a 12" flat angled tool rest for the mini in the near future. I'm always trying to improve on my existing equipement and I think a properly designed rest would be better than the round ones.

Re: Tool rest for Jet Mini

#12

Re: Tool rest for Jet Mini

Matt Berry

>Contact them, they have great customer service and can / will custom make something to your specifications / lathe.

Re: Tool rest for Jet Mini

#13

Re: Tool rest for Jet Mini

C.W.Stivison

>What size of angle are you thinking of using? (If it's not a trade secert)

C.W.