Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

palm??

Posts

palm??

#1

palm??

GaryG in MD

>A friend from CA sent me a couple half rounds of some kind of palm -- freshly cut. It's just a bunch of straws! Is there any hope for turning this stuff? I know the drill -- sharp tools, etc. But really -- is this worth even putting on the lathe? If I try it, would I be best served by first soaking it in wood sealer or something like that? How does one deal with this stuff, and is it worth the effort? Thanks, Gary

Re: palm??

#2

Re: palm??

Chip in Plano

>Like you said, you know the drill: sharpen constantly. You've gotta turn it anyway just to see for yourself. I call it needles. I did a small piece. I didn't pass the maid test. It fell from a shelf being dusted. It was ugly. Didn't have much fun but my skill level was way below my ability to deal with the challenge. Haven't bought any again. But I will just to see if I can do it well enough. I've seen red palm done well and it was really cool. I think CA might have helped but I didn't have any at the time.....

Now go off an turn it and report back. I might go buy some next weekend.

Re: palm??

#3

Re: palm??

Keith Newton

>Something to try. Band-saw, then rough turn the blank. This will give you a feel.

If it is impossible, soak it in water, then slip it soaking wet into a zip lock, then freeze it. If the space between strands is solid ice, you can probably get a good cut. After you get it down nearly finished, you can decide whether to soak with a polymer.

Re: palm??

#4

Re: palm??----kinda long winded answers

Wayne Allen - Carson City. Nevada

>Gary == I've turned palm before and it's really not that bad. As said before, sharp tools help give a cleaner cut. A couple of things-you will get the best results turning your piece "end grain", not like you would do for typical wood. I gather you have already split the rounds in half so this might be a moot point. But if you get more of this stuff, leave the rounds whole and cut out your blanks so as to give bowls and vases a vertical end grain orientation. Don't worry about the pith, there isn't any. The typical cross grain orientation makes a stringy mess.

When you cut this stuff, you are really never going to get a "smooth" wood like finish without using some type of a wood stabilizer like POLYALL. To turn this stuff without a wood stabilizer, as I said, you will not get a smooth finish after the piece is turned, so after it is cut to the finished shape, try spinning the piece and using a wire brush to give it a "fuzzy" finish. It really does give the piece a nice effect. Secondly, palm has a rather bland look and can have blotchy areas in it. To spice it up, bleach it first and then give it a bright coat of dye after it is turned and wirebrushed. Other than the dye, no finish is required.

There is a very nice example of this in on page 24 of the book "500 wood bowls".

Re: palm??

#5

Re: palm??

Jim King

>I am not an expert in palm but here it grows with a styrofoam like interior that can be pulled out by hand. The hardest part of the tree is the outside and the further in you go you enter the straw stage and then even softer. Imature trees or to far in the mature tree and you have this problem. Here is a photo of a log cleaned out where you can see the color change from the hard black outside to the strawlike lighter color.


img

Re: palm??

#6

Re: palm??

Darryl Hansen

>Gary, I think I have read about a process for soaking plam in a mixture of yellow glue and water and then letting it dry before turning it. Just a thought...Darryl (also in Md)

Re: palm??

#7

Re: palm??

Russ Fairfield

>If the Palm is still wet, stick it in the freezer, and turn the block of ice. If it is dry. soak it in a bucket of water before freezing. Stick it back in the freezer if it thaws while turning.

Re: palm??

#8

Thanks, and replies:

GaryG in MD

>Thanks, everyone, for the very thoughtful and interesting answers and the encouragement to play with this. Lots of good ideas there. I appreciate all your thoughts -- and your pix, Jim.

I hadn't heard about the "freezing" trick before -- that's a good one. I'll give it a try -- if I can get my wife to make room in the freezer! ;-)

The log is 7.5" in diameter and was already split down the middle into two halves when I got it. Since it was 15" long, I just made it into 4 half-rounds. I will try to turn a weed pot or something small in the end-grain orientation out of at least one of them -- for the experience, if nothing else. Should be interesting.

I looked at the one in "500 Bowls": I love the texture and I can see what you mean about turning it end-grain. It's too bad I don't have a full round to work with. Cross grain is probably going to come out looking funny as the grain direction changes around the circumference of the bowl. I'll have to come up with a shape that minimizes that somehow. I've never wire brushed a piece before, but I can see that this may be a time to try it. I'm reticent to try dying in the cross-grain orientation; I'm afraid it would come out very blotchy.

I've got a lot of wood backed up (the itinerant tree choppers just came through and decimated our neighborhood), but I'll post the results when I get to turning it (if they're presentable).

Thanks again, Gary

Re: palm??

#9

Re: palm??

GaryG in MD

>Darryl, Where in MD? ...Gary