Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Stacey Hager's Point Tool

Posts

Stacey Hager's Point Tool

#1

Stacey Hager's Point Tool

Dave Winters

>I've seen the video, never used one. Looks pretty straightforward to make from bar stock.

Lee Valley sells one that looks like a much larger dia. than what Stacy has...

Likes, dislikes, sources for it, Instructions for grinding.???

Thanks-

Re: Stacey Hager's Point Tool

#2

Re: Stacey Hager's Point Tool

Dominic Greco in Richboro PA

>Dave,

You wrote:

"....Lee Valley sells one that looks like a much larger dia. than what Stacy has...Likes, dislikes, sources for it, Instructions for grinding.???

"

Using information from Stacey Hager's article in last year's "American Woodturner" I made my own 3 point tool from 3/8" drill rod. After using it for some time, I made a smaller version using 3/16" drill rod. I found that I like using the 3/16" version much better. It just seems like it's easier to roll small beads and get into tight spots.

Ever since I made mine, I found that I can roll beads, both large and small, with greater ease and with much greater consistency. This tool has now become my "go to" tool for detailing.

Stacey's article shows how the proper angle and details how to make a very simple jig that will help you form the point more consistently. But I didn't need to make this jig since I used hex compression nuts for my ferrules. It's like I have a built in stop for the proper angle. I just rest one flat of the hex nut on my too rest, adjust the grinder table to the right angel, and go to town.

As far as sources for the rod, ENCO and MSC sell hardened drill rod in all sizes. Look for the M2 HSS stock if you can. Don't get too bent out of shape if the rod is only 6" long. A short tool is perfect for rolling beads.

Of course, you can bypass all this and just buy a 3 Point (or "Pyramid" as some call it) tool from Lee Valley, Packard Woodworks, Or CSUSA. But I believe the smallest diameter they sell is 3/8" (someone correct me if I'm wrong here).

Good luck,

See ya around,

Dominic

Re: Stacey Hager's Point Tool

#3

Crown Three Point Tool

Mike Brazeau

>I used the Crown Three Point Tool sold by Packard and LV and others briefly when I demoed my home made shock absorber version at our guild last fall. The Crown version has a much longer grind than Stacey recommends or I ended up with when I ground mine. It may be more useful for planing cuts with the longer grind. The handle is short and uncomfortable as compared to a standard lathe tool handle. You do not need much pressure or control though with the point tool. I have made a 1/4" version with a short fat handle, but haven't used enough to see if I can adapt to it. Can always remount in a conventional handle.

One thing I did not like about the tool Stacey makes, is the steel handle. He sent out samples to guild presidents and we have put ours in the guild library for trials by members. I found the tool unbalanced and the steel handle always feels cold. Even though I recall references to home made versions of the point tool at the rec.crafts forum a few years back, I thank him for introducing me to the tool through the AAW article in 2005 and the video clip. I absolutely love using it when I can. Makes nice uniform balanced beads with little effort.

Re: Stacey Hager's Point Tool

#4

Re: Stacey Hager's Point Tool

Doug Thompson near Cleveland

>I need to make one for Lou Ann in Indy. What is the nose angle? I figured the starting point would be 45 degrees. Any ideas...

Re: Stacey Hager's Point Tool

#5

Point Tool *LINK*

Mike Brazeau

>Doug - here is a desktop shot of my shock absorber version. The shaft is about 1 cm or 7/16" in diameter. After trying the Crown tool I lengthened the facets slightly by increasing the drop angle as I ground it. I don't use the Wolverine, but just hand hold it. Grinding is not difficult as it requires only a minor touchup. Can't say that it changed much in terms of actually using it. This very complicated angle finder thingey reads about 37 degrees as positioned. There was an article by John Berkeley of the UK in the September 2006 Woodturning, Issue No. 166 also. He mentions them being made by Hamlet. I have linked the picture from their web page as well where there is a good picture.

Mike


img

Hamlet Point tool

Re: Stacey Hager's Point Tool

#6

Re: Point Tool

Doug Thompson near Cleveland

>Mike,

Thank you for a very complete answer. I'll set this up on a dividing head then see what happens. This is a huge help.

Doug