Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

recent turning

Posts

recent turning

#1

recent turning

DavePowers

>I am looking for a better way to hold work piece. I have tried face plate with screws (chipped gouge). Two way tape does not hold to my style of turning (still learning light touch)

in process

[IMG]http://i83.photobucket.com/albums/j297/sdp72002/pot%20calls/pothollowedout.jpg[/IMG]

turned

[IMG]http://i83.photobucket.com/albums/j297/sdp72002/pot%20calls/potturned.jpg[/IMG]

finished

[IMG]http://i83.photobucket.com/albums/j297/sdp72002/pot%20calls/walnut3.jpg[/IMG]

Re: recent turning

#2

Re: recent turning 

DavePowers

>


img

Re: recent turning

#3

Re: recent turning 

DavePowers

>


img

Re: recent turning

#4

Re: recent turning 

DavePowers

>


img

Re: recent turning

#5

Keith Tompkins

Re: recent turning

keith tompkins

>Dave, one way to safely use a faceplate is to use a large faceplate, with the screws near the outer edge. Allow for the depth of the screws, and don't remove wood to that depth. reverse turning removes the material with the screw holes. Another option, which saves material, is to screw a waste-block to the faceplate, and use yellow glue to secure the blank to the waste-block. No danger of hitting the screws. Reverse turn the bowl to remove remainders of the waste block. Of course, a chuck will solve the problem altogether.

Re: recent turning

#6

Re: recent turning

Jennifer@Indy.USA

>Dave,

You and Melanie and the little man head this way and I'll get you going with this. Bring the tools you're using and we'll turn a little bowl and make sure that there are no holes in the bottom when we're done :)

After looking at this you might have a nice fly fishing reel in the works!

Next Wednesday will work for me.

Let me know. Mel has my number.

Jen

Re: recent turning

#7

Steve Kubien

Glue blocks

Steve Kubien

>Speaking of glue blocks... Can I use them on green wood with any success? My brain is telling me "NO!" because of the moisture. I'm guessing they are strictly for dry wood.

What say you?

Steve Kubien

Ajax, Ontario

Re: recent turning

#8

Re: Glue blocks

Ken Grunke from SW WI

>Steve, I'm not Keith but polyurethane glue (Gorilla glue for example) works good with green wood although I've not tried it with fresh, very wet wood. Most polyurethane glues say on the label to moisten the wood before applying the glue.

Re: recent turning

#9

Steve Kubien

I wondered about that

Steve Kubien

>I thought of that but worried that the bond from poly-u's was so strong that I may not be able to pop off the block. If I went this route, do I resign myself to reverse chucking and fully turning off the block?

So many questions. So little memory!

Steve Kubien

Ajax, Ontario

Re: recent turning

#10

Re: I wondered about that

Jorge Castaneda

>Steve,

What I do is this, attach something like a 1 1/2" oak block to the faceplate with steel screws, (no sheet rock screws!) turn that oak block round and flat, to this flat face, I glue a sacrificial 1 1/2' glue block, anything, poplar, birch even pine or spruce takin care the grain is across of the gran in the oak; you can use Ca glue or yellow glue or epoxie and I let is sit overnight and then turn away. The sacrificial 1 1/2" is good for about 4 usedthen you have to add another scarifial. I like that because creates a big space between the head and the work, it works for me...

Jorge

Re: recent turning

#11

Re: I wondered about that

Wally Dickerman in Arizona

>I don't quite understand the use of 2 blocks. I've been using glue blocks for a lot of years. I use med. CA glue and just about never have a failure. CA is instant, that is I install the block and immediately mount the piece on the lathe. It works very well with wet wood. It seldom happens, but if the wood warps a lot while drying it can pull away from the glue. Of course this would happen regardless of the kind of glue used. If there is a failure it's almost always because not enough glue was used. Just use hand pressure and there should be some squeeze-out. We use glue blocks in most of my classes, partly to show the student that they don't have to have a chuck to turn bowls. We turned a lot of bowls before the 4-jaw scroll chuck came on the market around 1990.

I usually use a screw-chuck with a glue block.

Wally

Re: recent turning

#12

Re: I wondered about that

Ken Grunke from SW WI

>Steve,

If "resigning yourself" to reverse chucking means having a nicer looking foot, then I say yes, it's worth the extra work.

Re: recent turning

#13

Steve Kubien

Re: I wondered about that

Steve Kubien

>Wally says, "It works very well with wet wood." Ok, CA is nice and easy. Thanks for the tip.

Steve Kubien

Re: recent turning

#14

Steve Kubien

Re: I wondered about that

Steve Kubien

>Hi Ken,

Re-reading my post I realize that I was anything but clear. Yup, I know I'll have to reverse chuck to make the base look good. What I meant was... Ummm... Sorry, brain's not working. Suffice to say, I know what you mean...an I think I mean something else.

I need a nap

Steve Kubien

Re: recent turning

#15

Re: I wondered about that

Jorge Castaneda

>Wally,

My explanation was incomplete, the pourpose of the double block is to create a space large enough between the headstock and work for the toolrest to fit confortably, that way I can work goth sides of say a platter without remounting.

I agree CA works on green wood and when I was talking about let it set overnight I was talking about the bond between the glue blocks, call it paranoia...