Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Best way to smooth out a tool rest?

Posts

Best way to smooth out a tool rest?

#1

Best way to smooth out a tool rest?

wilbur

>I finally got my old Walker Turner lathe set up last night and tried some turning. What I quickly noticed was that sliding the tools along the tool rest was very rough. Part of this is probably due to the backs of the old turning tools I was using not being completely smooth, but it feels like the tool rest itself is kind of rough as well.

Any recommendations as to the best way to fix this up? I thought about applying a lubricant/wax to the tool rest first, and going after the rough spots with wet/dry sandpaper.

Re: Best way to smooth out a tool rest?

#2

Re: Best way to smooth out a tool rest?

Greg Haugen

>When I get a "ding" or something in my tool rest I take a file to it. I file it from end to end in long strokes. That way the "dings" get out of it and it stays as flat as possible. Waxing it afterwards would help tools slide also.

Hope it helps,

Greg

Re: Best way to smooth out a tool rest?

#3

Re: Best way to smooth out a tool rest?

Ed Moore

>Wilbur,

If the rest is badly dinged then take it to the belt sander, place it so that the rest is parallel to the path of the belt, rock it back and forth as the belt is moving.

You get rid of the dings and the rest is straight if you are careful.

Apply floor wax before using.

Ed

Re: Best way to smooth out a tool rest?

#4

Re: Best way to smooth out a tool rest?

Doug Turner

>Several professional woodturners have recommended filing the tool rest. I like to flatten with a file and then epoxy a piece of 1/8" diameter stainless steel weld rod along the top. The weld rod doesn't knick and when worn can be replaced.

Re: Best way to smooth out a tool rest?

#5

Re: Best way to smooth out a tool rest?

Ken Grunke from SW WI

>I use a 4" angle grinder with an 80 or 100 grit sanding disc but it must be moved evenly across the rest's edge to avoid making dips. A portable belt sander might work better, but never tried it. A big coarse file is probably the best, especially a new one. After getting the nicks out, I slicken the edge up with a fine grit of sanding belt material.

Re: Best way to smooth out a tool rest?

#6

stainless welding rod

Mike Nelson

>Doug, My tool rest has a couple of good dings that musta happened before I became a pro ;) What kind of epoxy are you using and will it hold up to uh, 'professional' use?

Re: Best way to smooth out a tool rest?

#7

Bob Moffett

Re: Best way to smooth out a tool rest?

Bob Moffett

>I went to a demo by John Jordan this past weekend and he said to use a file and then wax the toolrest with paraffin.

Re: Best way to smooth out a tool rest?

#8

Re: Best way to smooth out a tool rest?

Chip in Plano

>I used a sheet of sand paper tacked to my table saw. Then I ran the tool rest back and forth to flatten it. I marked ding, nicks, voids with a black marker and worked them all out. But I've also used a file (when I can find it). Belt sander isn't one I thought about but nice to know 3 ways to accomplish something.

Re: Best way to smooth out a tool rest?

#9

Re: Best way to smooth out a tool rest?

Dave Peebles Lyons, Ohio!

>Bob,

I do the same as John. Of course, that is who I learned this from.

It has been working for over ten years. A Bastard mill file is your friend. :) It is quite easy for me to take a couple of light passes on the tool rest to clean it up, followed by a quick swipe with a bit of canning wax. Slick and smooth is a good thing. :)

Dave

Re: Best way to smooth out a tool rest?

#10

Re: Best way to smooth out a tool rest?

eliot d

>I believe the best and easiest method is to leave the tool rest on the lathe and use a regular hand-held orbital sander. The sandpaper grit should be chosen according to the condition of the tool rest. Obviously, you can move up to higher grits to get it smoother and smoother. If it's just a little rough, I find a terrific method is to remove it from the banjo and smooth it up on a wire wheel.