Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Stuck chuck - Not quite

Posts

Stuck chuck - Not quite

#1

Stuck chuck - Not quite

Bill Crommett

>In trying to change the long nose jaws on my Vikmark -100 chuck I am having trouble removing the number 3 jaw. Both of the screws refuse to budge even after several days of penetrating oil applications. I suspect that the problem exists because the last time I used the chuck was on some green wood that spewed moisture around and some got into the screw threads. All sugestions will be considered, at least briifly -- even those that say "send it to me ".

Bill

Re: Stuck chuck - Not quite

#2

Stuck chuck - Not quite

nailshooter

>I had the same problem with mine the first few times I changed the jaws out. Finally, one time I had one side fo the jaws that just wouldn't budge. I dont' remember which jaw set it was, but it was as if the screws were welded in position. I even resorted to soaking the whole chuck "break free". No help.

Called the group I bought it from (KMS tools) and they told me that the tolerances were such that it happened from time to time. Take a look a the screws, too. They are anodized or coated, and they are on bare metal when installed. They were unable to help.

I finally needed the other jaws in the chuck so bad that I put the chuck in vise, hit with some break free and muscled out the screws. I thought for sure the hex key would break, but it didn't. I figured if the head(s) broke off, I could either drill out the remaining stub and grab what was left with vise grips after removing the jaws, or I would get lucky and they would shear at the bottom fo the head. However, the simply chirped when they broke loose, then came out. I did slightly strip one of the screw heads, but purchased one to replace it from KMS. Those screws are their design, and it has to be one of theirs, so if you order get a couple extras for "just in case".

Now I put a tiny bit of grease on the tips of the screws before assembly if I change the jaws and make sure not to overtighten. No problems since then.

Robert

Re: Stuck chuck - Not quite

#3

Keith Tompkins

Re: Stuck chuck - Not quite

keith tompkins

>Bill, take a punch that will fit in the recess of the stuck screw; even better, cut off an allen key of the appropriate size. Then tap the punch or the cut-off allen key with a hammer. If you have a hand-held impact driver, that will work great. Either method will break the threads free. It's good to keep a few spare set-screws on hand.

Re: Stuck chuck - Not quite

#4

Re: Stuck chuck - Not quite

John Lucas

>I recommend what both have said. I find that tapping the screws while applying penetrant will help the penetrant go in. I do this for several days sometimes several times a day if I'm in the shop, and have almost always been able to get some really rusty things apart. After you do get them out apply a very tiny amount of antisieze compound and you won't have that problem anymore.

Re: Stuck chuck - Not quite

#5

Jesper, Denmark

Ask Stuck Chuck Canuck......

Jesper, Denmark

>Jim Shaver.

Sorry Jim, but that little episode several years ago is maybe forgotten by most, but I still chuckle.

Re: Stuck chuck - Not quite

#6

Re: Stuck chuck - Not quite

Bill Turpin in WNC mountains

>Put a hot soldering iron to the head of the screw and heat for several seconds. Allow to cool and apply penetrant. Repeat process several times.

Bill in WNC mountains

Re: Stuck chuck - Not quite

#7

try alittle heat with small torch

robert davis

>

Re: Stuck chuck - Not quite

#8

Re: Ask Stuck Chuck Canuck......

Bill Crommett

>Jesper : I hadn't forgotten that one but I thought a bit of restraint was in order.

B

Re: Stuck chuck - Not quite

#9

Re: try alittle heat with small torch

Bill Crommett

>I would like to thank everyone for the help shown today (except Jesper, because he likes to open old wounds ). The solution was a light bit of heat from a propane torch. I will, however use a small dab of greese in the future. Thank you all.

B

Re: Stuck chuck - Not quite

#10

Re: Stuck chuck - Not quite

Jim Swank

>Yes to using a cut off hex key and rapping with a hammer. If you use a punch, it should have a flat tip. Don't pound like a blacksmith, but give it several good raps. It's also worth while giving several good raps to the stuck jaw directly. An impact wrench is great to break stuff loose if you have one and can fiit the hext key shaft to it.

Heat, as suggested below, can also work at times, but is best saved as a last resort.

Re: Stuck chuck - Not quite

#11

I Still Get a Good Laugh From It !!!

Jim Shaver - Oakville, Ontario

>

Re: Stuck chuck - Not quite

#12

Re: Stuck chuck - Not quite

Walt Ahlgrim

>I find that a T handle Allen wrench will transfer much more torque to the screw. With the L wrench pressure is all on one side and this damages the heads of the screws.

Re: Stuck chuck - Not quite

#13

Jesper, Denmark

Fond memories are nice to have......

Jesper, Denmark

>I think of you every time I try to remove the chuck to change it to another one.