Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Filling cracks in cherry??

Posts

Filling cracks in cherry??

#1

Filling cracks in cherry??

Bill MacLachlan

>Interesting suggestions listed below on filling a crack in walnut. What would you suggest for cherry? I have been playing with turning a few small ~6" bowls, some NE and some not. I have finished sanding and applied 1 coat of BLO on the one in question. Was this a good idea or should it be done pre-finish?

I was given some small pouches of colored sand from Woodchuckers and after reading the post below, was thinking of trying the a red sand. Would this sand be as fine as coffee grounds? How small of a grind is the coffee? Do you want it course salt-like or almost a powder? (this coming from a non-coffee drinker!)

Thanks, Bill

Re: Filling cracks in cherry??

#2

Re: Filling cracks in cherry?? *LINK*

joaz

>I have never used sand but it should work fine. You could also try staining it the colour you want.

I usually use the sanding method: Put CA in the crack to toughen the fibers...let it dry. Sand around the crack until it fills with sawdust...apply the CA again...let dry. Continue until crack is filled and hard. Sand level.

I know some folks don't like the looks of this method but I have used it on cherry a lot and it works for me.

Note:: don't use accelerator as it will turn the sawdust white!


http://www.maine-web.com/woodturning

Re: Filling cracks in cherry??

#3

Re: Filling cracks in cherry??

Barbara Gill, Remlik VA

>I have used CA and the little bits of brass from a key making machine. Yes, I know it isn't all brass but around here brass predominates. I also use the coffee and epoxy for larger voids. I would think sand would be hard on the tool edge.

Re: Filling cracks in cherry??

#4

Re: Filling cracks in cherry??

Mac

>Hi Bill, I dont know if the cherry that you have,has small black spots or streaks in it. Ours up here does,so I use 5 minute epoxy(Devcon brand) and I mix ebony dust in with it.Soot from a stove pipe will work,as well as acrylic colors.It machines and sands to look just like the streaks in the wood.Give it a try. Sometimes accenting a fault looks better than trying to hide it....

Re: Filling cracks in cherry??

#5

Re: Filling cracks in cherry??

Mike in Shreveport/Bossier City, LA

>Hi Bill,

One method I'm doing a little experimenting with and mentioned in another post was using embossing powder. It's finer than the sand and in some cases, coffee. It comes in a huge variety of colors and can be mixed with epoxy or use the CA fill method. It's very easy on the tools. I'm still perfecting the epoxy method (quantities, etc...) but with CA, the powder will darken just a little bit. It'll look kinda ugly when you sand but when you get to the finer grits and put that oil on it the color will pop!

Mike

Re: Filling cracks in cherry??

#6

Ground red shale

Mike Brazeau

>I have used ground red shale powder for cherry and it works well. I grind with a mortar and pestle and sieve through a bit of panty hose. It achieves almost the same color as the pitch inclusions often present in black cherry. I got the idea from the mineral powders that LV sells. As noted above the embossing powders are excellent. Haven't used but they are used successfully by a fellow guild member.

Re: Filling cracks in cherry??

#7

If the colored and is really sand,

Don Henthorn

>I think it would be exceedingly hard on tools.

Re: Filling cracks in cherry??

#8

Re: If the colored and is really sand,

Tom Storey

>It is!! DAMHIKT! Some use the toner from laser printer mixed with epoxy. You must be very careful with the toner because it gets onto everything and is a 'B' to get off. DAMHIKT too!!

Tom

Re: Filling cracks in cherry??

#9

Re: Filling cracks in cherry??

Bill MacLachlan

>Thanks for the great tips guys. I really like the embossing powder (once I found out what it was!!)

And yes the stone is very hard on tools. I found this out when I added a single ring to the top of an ash bowl I recently turned. Will post when I finishing buffing.

Re: Filling cracks in cherry??

#10

Re: Filling cracks in cherry??

David Breth

>One more - I had some small splits to fill in a spindle one time, and somebody suggested using charcoal - like from the fireplace. Since that kind of dark line occurs in cherry anyway, it didn't really look like a fix. Just some ca glue mixed with it, worked like a charm.