Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

dyeing

Posts

dyeing

#1

dyeing

dwfII

>So...I've got my elm HF turned, sanded and polished. After polishing (with up to 4000 grit abralon), the surface was beautiful...so smooth it almost doesn't need further finishing.

Monday I dyed it.

But when it dried, the dye (an alcohol based aniline dye) must have raised the grain because now I feel considerable roughness on the surface.

My question: how do I sand or polish this roughness away without sanding off the dye? Or do I just have to re-dye and sand and re-dye and sand until the grain is no longer rough and my colour is intact?

DW

In the High Desert of Central Oregon

Re: dyeing

#2

Re: dyeing

jeff myroup

>In my experience I have found that if I sand past 220 the dye does not penetrate as well. I usually sand to 220, dye, then resand upto 400 or 600. I then apply my finish. Did you get good penetration with the dye sanding to 4000?

Jeff

Re: dyeing

#3

JL

Re: dyeing

JL

>Whenever I use water based or alcohol based dyes on my pieces (furniture, not hollowforms), I typically raise the grain a couple of times with judicious "baths" and sand afterwards. Then I use the dye. Of course I'm only going to 320 or 400 at most.

That being said, I think that you can probably "knock down" most of the "fuzzies" with gentle sanding. You may need to re-dye it, you may not.

Re: dyeing

#4

Re: dyeing

john lucas

>I agree with JL. I would start with 600 grit and do it very lightly. You still may have to redye. I wet the wood and sand the nibs off a couple of times before dyeing. I sand to 220 then wet the wood and sand this with 320. Then I wet the wood again and sand to 400. I'll dye the wood and sometimes sand with 600 grit or 4/0 steel wool. Depending on the wood it will sometimes require another application of dye. I finish after this. I reserve the really fine grits for after the finish in this application.

Re: dyeing

#5

Re: dyeing

dwfII

>Thank you. I have the vessel off the lathe so sanding will not be as easy as it was but I think I understand what I need to do. Looks like I went about it kind of backwards, initially.

Thanks for the help.

DW

In the High Desert of Central Oregon

Re: dyeing

#6

Re: dyeing

john lucas

>Sanding is easy off the lathe. Sanding is really a bad word for this because all you want to do is knock off the nibs. Fine sandpaper and a very light touch is all that's needed. You should be able to sand the nibs off in 5 minutes or less.

Re: dyeing

#7

Re: dyeing

Donna Banfield

>I recall during a demo that Andi Wolfe did at Totally Turning a few years back, that she 'prepped' the area she was coloring with 91% Isopropyl Alcohol. She did this to prevent raising the grain and then proceeded to apply the color with the Prisma Color Art Markers.

I wonder if this would work? I am curious if this has been tried by others, because I have an idea about using aniline dies on a piece that will be carved, i.e., turned, sanded, carved, dyed. The carving will be so intricately detailed that any amount of sanding will be virtually impossible.

What do you think?

Re: dyeing

#8

Re: dyeing

Russ Fairfield

>There are a couple ways around the grain raising problem if you can't or don't want to raise the grain before dying the wood.

The easiest is to use an "Oil Soluble" dye that is soluble in Toluol, Turpentine, or a high grade lacquer thinner. Since neither water nor alcohol is used, there is no grain raising. A good source of oil soluble dyes is Woodworker's Supply.

Or, you can use an alcohol soluble dye if you seal the wood with lacquer before dying it. Brush it on and immediately wipe away all of the excess. The lacquer keeps the wood fibers in place, and an alcohol solvent dye will penetrate the lacquer. Try this on scrap before using it on the real thing.

Re: dyeing

#9

Re: dyeing

Ron in Drums PA

>The other 9% of 91% isopropyl alcohol is mostly water. The grain can still raise.

Re: dyeing

#10

Re: Thanks Russ & Ron (NM)

Donna Banfield

>

Re: dyeing

#11

Re: dyeing *LINK*

Darrell Feltmate

>I like the Fiebings leather dyes for wood. They are alcohol based and I cut them with methyl hydrate which would be denatured alcohol in the States. When there is grain raising with them, I knock the nibs back with 1500 grit wet or dry used damp with a touch of methyl hydrate. This is really fast sanding if, as John said, one can call this sanding at all. Dyes should penetrate well even after sanding to 2000. These are not stains which have a solid content but dyes that affect the fibers of the wood.


Around the Woods