Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

jet 1236 index pins

Posts

jet 1236 index pins

#1

jet 1236 index pins

Stephen

>Hi All,

I bought a second hand 1236 that I am tinkering/learning on. (I am learning that I probably should have known more about the lathe before I purchased.) It did not come with the index pins. I looked on the jet site, and I can purchase them for about a dollar a piece with a whopping twenty dollar shipping fee.

I am going to look locally, but do you have any advice on whether an appropriately sized and threaded bolt would accomplish the same thing? Any help on those dimensions?

Thanks, Stephen

Re: jet 1236 index pins

#2

Re: jet 1236 index pins

Wolf Kiessling

>I have experienced this in the past myself, where I needed to mail order a one or two dollar item which was accompanied by a huge shipping fee. I have successfully called these companies and explained to them that I needed the small item but did not want to pay the shipping fee. In every case that I remember, the companies shipped the item and charged me ACTUAL shipping fee which might have been a buck and a half. Don't know if Jet would do this but it's probably worth a try. It certainly couldn't hurt and the call is generally a free 800 call.........

Re: jet 1236 index pins

#3

Re: Stephen- I'm not sure what ........

Jamie Donaldson

>.. index pins you reference? Most parts of that type should be juryriggable(is that a word?) from a well stocked hardware store.

Re: jet 1236 index pins

#4

Re: jet 1236 index pins

Rick Allen

>You might find a drill bit to be of the desired size, of good quality steel and readily available at the "borg".

Re: jet 1236 index pins

#5

Re: Stephen- I'm not sure what ........

Don in Central Illinois

>If it wasn't a word before, it is now.

Re: jet 1236 index pins

#6

Re: jet 1236 index pins

Jim Terry

>Stephen, I have the Jet 1642 and the index pin for it is 5/16-18. May be the same for the 1236. About 1/4 inch of the threads should be ground off from the tip.

Jim Terry in W-S, NC

Re: jet 1236 index pins

#7

Re: jet 1236 index pins

John Lucas

>Stephen If you will sketch out exactly what you need I may be able to juryrig one. I'm not that familiar with the Jet 1236.

Re: jet 1236 index pins

#8

Re: jet 1236 index pins

Troy German

>Stephen,

I ordered the same thing for my 1236 (should arrive today). The freight was only $5. I odrered over the phone, maybe the internet freight calculator is wrong. By the way, I'm in Calif. but don't know where it shipped from.

Troy

Re: jet 1236 index pins

#9

Re: I'll send you one free

Charlie Anderson

>When I sold my 1236 I forgot to give it to the buyer and I never knew how to contact him. That was 6 months ago so I doubt I'll hear from him. email me you address.

Re: jet 1236 index pins

#10

Re: jet 1236 index pins

Ken Grunke from SW WI

>Stephen,

It is 5/16 x 18 tpi. The index holes in the spindle are smaller than that.

I also have a pre-owned 1236 without the index pin, so I used a long 5/16" bolt, chucked it in my scroll chuck, and filed the end to a taper on the lathe, about 30 degrees included angle. I then bent the bolt at a right angle to give a handle.

I had been using the knockout bar as a spindle lock in the lower hole, so I had to clean up the threads with a tap. Now I use the lower hole for indexing, and the upper hole for spindle-locking.

Re: jet 1236 index pins

#11

Thanks all

Stephen

>I appreciate all the replies and ideas. I have emailed Charlie to take him up on the offer (can't beat that generosity).

Just figures that jet would charge $2 for a 10 cent bolt...

Thanks again.

Re: jet 1236 index pins

#12

Re: I'll send you one free

David Breth

>If you live in Rochester, NY, rest easy, I gave up and bought them.

And I didn't have to pay too much for shipping....