Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A natural, durable finish with minimal coats and fuss popular among woodworkers, flooring professionals, and furniture makers

MDF glue block

Posts

MDF glue block

#1

MDF glue block

gary s clarke

>I need to glue and turn the top 3" of a segmented bowl ( 10 in in D)

and want to use a glue block. Options are MDF, plywood, or solid wood like poplar. Any suggestions? I am thinking about using MDF because it is easy to use. Will it hold using glue or double stick take? I could also use any of the other options. Suggestions would be greatly appreciated. thanks in advance.

Re: MDF glue block

#2

Re: MDF glue block

Jimiles-Charlotte, NC

>Gary:

I do almost all my turning on glue blocks.

Avoid plywood. It has voids and will come apart.

I collect scrap ( spruce, pine Fir ) 2x4, 2x6 & 2x8s from construction sites. They will usually give you all you want.

I plane one side for a glue joint and cut them the widest width of the bowl so I can use clamps to hold while glue ( titebond) sets.

I normally turn the bottom of the piece first and use flat nose scraper to get it flat to be glued. cut a 1/8" dimple in center of bottom. drill hole in center of your glue block. Use nail through glue block to dimple to center your glue block so that when you mount faceplate you can use this mark to get it as close to center as possible. I will part off the glue block off when I complete the turning and saw the last 1 -2" depending on size. make sure screws into faceplate aren't too long to prevent parting off glue block.

Re: MDF glue block

#3

Re: MDF glue block

Jerry Hall

>I have had a lot of MDF scrap on occasion, and it works fine, even with a tenon for my scroll chuck. I prefer real wood however because even a little turning of the MDF is a dusty mess, and I don't like breathing that unknown concoction. If you have to do any facing when trueing between centers before mounting on a chuck it is a bunch of dust. Still, I do use it.

Re: MDF glue block

#4

Re: MDF glue block

gary s clarke

>Jim, I have used lots of glue blocks for segmented bowls, however I have not used a glue block for a 10" Dia ring for the top of a bowl. I was just wondering if MDF would work for a 10" ring. Has anyone used it without fear of not holding well enough? I usually use poplar for my standard glue blocks,any it works well. Just trying to not have to glue several boards together to get a 10 inch glue block of poplar.

Re: MDF glue block

#5

Re: MDF glue block

Mark Kauder, Phenix City, AL

>Gary,

Avoid anything but solid wood for waste bocks. MDF and Plywood have a habit of coming apart with catastrophic results.

Even pine is better.

Mark

Re: MDF glue block

#6

Re: MDF glue block

Jimiles-Charlotte, NC

>I'm not sure I understand why you are using a glue block for a ring that will be placed on top of a bowl? If it is to "face it off", flatten it so there will be accurate glue joint with the bowl? If so then there are probably other ways to do that. You may be able to sand it flat. I have a large circle of MDF that I run small screws through the back into the ring, mount on lathe and flatten. Double stick tape or hot glue on same circle some people like. I also will sometimes leave the band clamp around the ring a little loose after gluing the ring and immediately glue it to the top of the bowl and weight or clamp. You may not get a perfect joint, a burn line can disguse. Does this ansewer your question?

Re: MDF glue block

#7

Re: MDF glue block

gary s clarke

>thanks Mark, guess I was being lazy, thinking I could get by without gluing some wood together by using MDF.

Re: MDF glue block

#8

Re: MDF glue block

Russ Fairfield

>MDF has almost no tensile strength, and there should be a message in the fact that you can pull the MDF from the surface with carpet tape when it is removed.

That doesn't mean you can't use it to hold a single ring, but I would definitely not recommend using it for anything with more weight or overhang than that, and definitely not for a waste block on a larger piece.

Re: MDF glue block

#9

MDF is good for jam chucks

Ron in Drums PA

>Small ones anyway. Great for box lids

Re: MDF glue block

#10

Re: MDF Sux with chucks!

Bart Castleberry

>Never had good luck with it when used with chucks, the jaws crush it and a dovetail in it causes the jaws to split it. It splits very easily along it's thickness, almost like it was layers of paper glued together but with really crappy glue, wait... it is pretty much paper. Go figure. It will seperate while turning. I know.

Second vote for framing scraps, though I often have oak scraps that I use and like more.

Re: MDF glue block

#11

Dick Hines

Re: MDF Sux with chucks!

Dick Hines

>I use frameing studs for glue blocks. I have been useing the 2x4 stud I bought 2 years ago and still have some left. I use a 2" hole saw and cut 5-10 out at at time. Place the blanks in my chuck and turn them uniform. I will use one until it will not extend out of the chuck. When turning ornaments I may 10 glued up at one time.

I have 2 jam chucks made out of MDF. I have one piece 12" in D and one 20" D. I put a face plate on each and then glue a piece of sheet cork on the other side. Then when I need to finish the bottom of a bowl I bring up the tail stock and jam the bowl between the tailstock and the MDF board. Not as good as a vacium chuck but a lot cheaper.

Re: MDF glue block

#12

Re: MDF glue block

David Walser

>It's interesting the varied experiance we all seem to have, even when using similar materials. With regard to using MDF for glue blocks, Malcolm Tibbetts, in his book, The Art of Segmented Wood Turning, recommends using MDF for glue blocks. So, despite what some have said -- and I in know way doubt their experiance -- MDF can be used as a glue block for segmented turning.

The advantages of a MDF glue block is that the materials is stable, uniform, and extremely flat. Malcolm uses MDF glue blocks for flattening rings as follows: first, on the disk sander, sand one side of the ring flat. Attach the ring with hot glue (yes, hot glue) to the MDF glue block (sanded side towards the glue block) and turn the ring true. Using hot glue requires taking very light cuts -- which might explain why Malcolm did not warn about MDF coming apart as others on this list have experianced.

In addition to hot glue, the book shows double sided tape and yellow glue being used with MDF glue blocks.

Re: MDF glue block

#13

Re: MDF glue block

David Walser

>For some reasons my edits to my post, above, did not take. Here's what it was supposed to look like:

It's interesting the varied experience we all seem to have, even when using similar materials. With regard to using MDF for glue blocks, Malcolm Tibbetts, in his book, The Art of Segmented Wood Turning, recommends using MDF for glue blocks. So, despite what some have said -- and I in no way doubt their experience -- MDF can be used successfully as a glue block for segmented turning.

The advantages of a MDF glue block is that the material is stable, uniform, and extremely flat. In the book, Malcolm has several photos showing several rings that have been stacked, one by one, onto an MDF glue block. Malcolm uses MDF glue blocks for flattening rings as follows: first, on the disk sander, sand one side of the ring flat. Attach the ring with hot glue (yes, hot glue) to the MDF glue block (sanded side towards the glue block) and turn the ring true. Using hot glue requires taking very light cuts -- which might explain why Malcolm did not warn about MDF coming apart as others on this list have experienced. Hot glue allows the ring(s) to be taken off of the glue block very easily. (Having to part the ring off or pry it off risks breaking the ring.) Hot glue also allows the glue block to be used several times.

In addition to hot glue, the book shows MDF glue blocks being used with double sided tape and yellow glue.

Re: MDF glue block

#14

Re: Where's the argument

Russ Fairfield

>I don't see any conflict here at all. There is a world of difference between attaching a single segmented ring to an MDF faceplate, and using the MDF as a waste-block that is glued to the bottom of a bowl for chucking and turning the entire bowl. MDF is entirely suitable as a faceplate material for a single ring or a platter, but there are a lot better things to use as a waste-block for turning a bowl. Any confusion in this thread could be from calling both a "waste-block".