Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

Cherry Platter Quandry

Posts

Cherry Platter Quandry

#1

Cherry Platter Quandry

Mikefrom Tn.

>One thing for sure, I respect all the platter turners out there. I'm afraid if I turndown the center I'm going to spin it out. What do I do? Go ahead and then fill? I know the critics don't like that. I was using this as a learning exp. but I'd like to save it if I could. I'd leave it but it just sticks out there and ruins the lines. What would my friend John Lucas do?


img

Re: Cherry Platter Quandry

#2

Re: Cherry Platter Quandry

john lucas

>Mike I assume your saying that the middle is too thin and if you turn down the center section to get rid of those marks then you'll cut through. Is that the problem? Well I certainly can't say that I've never done that. I've patched them by putting another piece of wood in there. The trick is getting it to not look like a mistake. Whatever you do will draw your eye right to it.

You have to be aware that most non turners don't know that we've made a mistake and covered it up. The fun part is trying to get it past other turners. My most successful saves were to put a piece of wood the same color and carving on it so the difference in the wood isn't as noticeable. The other good save was that I turned a bowl and inserted the foot in the hole. This made sort of a chip and dip bowl out of it. I turned the bowl to fit a glass bowl that I bought so you could actually remove the glass bowl to clean the dip.

Good luck. John

Re: Cherry Platter Quandry

#3

Re: Cherry Platter Quandry

Bob Fawcett

>One thing that comes to mind is to turn the groove through, mount a ring of contrasting wood like Walnut, and put the center back in. It would look like an inlay.

Re: Cherry Platter Quandry

#4

Thanks John!

Mikefrom Tn.

>I think I like the glass bowl idea. It would make it look planned and not poor exicution. As this is my fist "big turn" I've learned a few things. First make sure the mount is true. I did'nt think I was off much at center, but go out 21" and well, guess the rest. I thought I had contrasting color all the way around but once I turned awhile it bcame evident that I didn't. I'm hoping that some natural stain will darken the outside ring back up. I wanted a little more tapertowards the center but became worried that I was getting too thin.If I decide to cut out the center I probally be able to correct that. I'm going to turn the center down eitherway and take my chances on there being enough wood. I should have turned the center down to the correct depth first and then worried about the outside ring but with the wobble I had I didn't know if I was going to have to remount or not So I left it to last. Big mistake. We'll see what happens.

Re: Cherry Platter Quandry

#5

Re: Cherry Platter Quandry

Bill Neddow

>Do not turn out that bump in the center. Carve it into a decorative element, or simply put a little bead on the outside, and a couple of shallow coves inside that -- kind of a medieval shield, (or rosette).

Re: Cherry Platter Quandry

#6

Re: Thanks John!

john lucas

>Mike I don't know if I can describe this well enough but I have a method of measuring bottoms that I learned from someone a long time ago. Use a framing square to mark a line on your lathe bed where the bottom is. If your using a chuck it will be the tip of the jaws.

When your turning the front use the framing square sitting on the lathe bed and touching the lip of the bowl. Put a mark on the lathe bed, or you could use masking tape. Now measure from the framing square to the front side bottom of the bowl or platter. Go to the lathe bed and measure from your masking tape mark, the distance you just measured. This will show you exactly how much wood is left in the bottom.

If that doesn't make sense I'll try to take some photos tonight.

Re: Cherry Platter Quandry

#7

Re: Thanks John!

Cyril Griesbach

>Nice technique, John. Thanks.

Cyril

Re: Cherry Platter Quandry

#8

Re: Cherry Platter Quandry

John Uteck

>I'm going through the same problem right now ---- mine cracked when I reverse turned it with a vacuum chuck. The crack didn't split the entire platter, but just enough in the middle that I had to do something about it. I first tried adding a plug on the bottom side into my chuck recess -- that helped make it solid again, but didn't look quite right, and I can still feel the crack from the top side.

Next, I thought about cutting the middle out, and adding a marble tile insert and make a complimentary cheese knife. A co-worker suggested a pottery tile from one of the paint-it-yourself places, and get the kids involved with decorating. I will try this idea when the local pottery painting place receives their back-ordered tiles.

Re: Cherry Platter Quandry

#9

Re: Cherry Platter Quandry

Bill Hale

>Mike

Nice piece and no problem with the error.

You might consider turning another piece to put on top of the error. Eg. Add a raised insert to put a dip bowl into, same or different wood. You can buy a small bowl at Walmart for only pennies and make the piece to fit it. Sell or give away together.

Those big pieces sure do make you hold your breath don't they.

Good turning and be safe

Bill in Show Low, AZ.